F-1â¢ Installation Manual - Viking Access

More documents

Recommendations

Info

VIKING PIPE STAND Part No. VA-F1PS For Viking F-1 & R-6 Vehicular Gate Operator Standard Features • Main pieces made of 1/4” thick material • All hardware included Installation 1. Remove Chassis Reinforcement Brackets and Bolts 2. Place Operator on Pipe Stand 3. Replace Chassis Reinforcement Brackets 4. Attach the Operator and Brackets to the Pipe Stand using the Mounting Bolts, Nuts and Washers supplied with the Pipe Stand 5. Tighten Bolts securely 6. Refer to F-1 or R-6 Manual for Plan of Installation 3.05" I.D. F-1 Gate Operator (sold separately) 3.10" 10.85" 2.15" Mounting Bolt Washer Reinforcement Bracket F-1 or R-6 Gate Operator 13.49" 8.05" 2.79" 3.00"O.D. Pipe (Maximum) Pipe Stand Washer Mounting Nut Secure Stand to Pipes Using (6) Supplied Bolts Note: All Mounting Hardware Supplied with Pipe Stand Grade Level Consult Local Codes for Depth and Concrete Requirements 34 TECHNICAL SUPPORT 1 800 908 0884
Cha Gnd Power Power Check M Low Low Battery Battery UL Sens ector UL Rec. Off 1 Radio Gnd UL Sens +28v Reopen Loop 24V OPTIONAL VIKING BLUE INSTALLATION Center Loop OPEN LEFT Radio Rec. JP2 OPEN RIGHT Radio Station If you are using the computer: • Hold the computer near the Gate Operator. • Run the application by clicking the icon on the desktop. • Select “Setting” in the top right of the screen. If you are using a PDA: • Hold the PDA near the Gate Operator. Gnd Sensor min. MAX Obstruction Mag. Lock Radio 1.5 MAG. Mag. LOCK Lock Loop Conne Overlap Delay +28v 0 eopen 30 Hold Open Timer Gnd 3 Charger Power Low Battery Check Motor N.C. COM N.O. Gnd Center Gnd 60 Open Match up White Dots Install Jumper JP3 JP2 +28v Exit Gnd Open Open Commands Commands Stop JP3 Strike Gnd Close C35 C36 Fire Gnd Open Stop Guard Guard Station Station Close GND 1. Insert CD into host computer 2. Install MS ActiveSync (check your computer, it may already be installed to communicate with a PDA or smart phone. 3. Install Viking Blue software Select Install Viking-Blue for PC (to have the computer to communicate with the Operator) Select Install Viking-Blue for PDA (to have the PDA to communicate with the Operator) WARNING: If this PDA is a new device, turn off all options when syncing with the computer. For either installation, follow the steps in the user manual. 4. Plug the Viking Blue Module into the Viking Gate Operator Control Board. WARNING: Connecting the plug backwards can result in damage to the Control Board and will render the Viking Blue Module useless. Use care in connecting the plug to the Control Board. The pins are small and easily bent. Match the white dot on the plug to the white dot on the control board (near the JP2 legend as depicted). 5. Install the Jumper (near the JP3 legend depicted). Viking-Blue requires this jumper to operate. The “Low Battery” LED will turn ON, indicating the Control Board is ready for use with the Viking-Blue Module. 6. Open Viking Blue software on the chosen device. Brake Open Stop Master/Slave Master/Slave Close GND Siren • Select “Start” and “Programs”. • Click the Viking-Blue Application. • Select “Connection” on the toolbar. • Click “Search” (looking for available Viking devices). • Select the Operator you want to communicate with. • Click “Connect” to start communication. The Light on the Viking-Blue module will turn green upon connection to the Computer or PDA. Follow the steps in the user manual. . 28 TECHNICAL SUPPORT 1 800 908 0884 Se habla Español 35
Page 1 and 2: VIKING installation instructions an
Page 3 and 4: F-1 Vehicular Gate Operator • Rev
Page 5 and 6: TABLE OF CONTENTS Parts Diagram/Par
Page 7 and 8: IMPORTANT SAFETY INFORMATION WARNIN
Page 9 and 10: IMPORTANT SAFETY INFORMATION CAUTIO
Page 11 and 12: IMPORTANT SAFETY INFORMATION WARNIN
Page 13 and 14: IMPORTANT INSTALLATION INFORMATION
Page 15 and 16: PLAN OF INSTALLATION - DETAILS Conc
Page 17 and 18: GATE OPERATOR INSTALLATION Step 4 U
Page 19 and 20: ELECTRICAL INSTALLATION - SINGLE UN
Page 21 and 22: NO COM LIMIT SWITCH SET-UP Opening/
Page 23 and 24: ELECTRICAL INSTALLATION - MASTER/SL
Page 25 and 26: VEHICULAR LOOP DETECTOR INSTALLATIO
Page 27 and 28: ACCESSORY CONNECTIONS 1 2 Photo Bea
Page 29 and 30: Power S R R M-2 ELECTROMAGNETIC LO
Page 31 and 32: SPECIAL FEATURES Auto-Open Feature
Page 33 and 34: SPECIAL FEATURES 2 1 COM N.C. Motor
Page 35 and 36: BATTERY & EMI BOARD LOCATION The Ba
Page 37: ctor Radio Station SOLAR PANEL INST
Page 41 and 42: TROUBLESHOOTING Gate does not open
Page 43 and 44: our continuous commitment to excell

F-1â¢ Installation Manual - Viking Access

Create successful ePaper yourself

Delete template?

Save as template?

F-1â¢ Installation Manual - Viking Access