Chapter 3 Wiring Methods and Materials
Chapter 3 Wiring Methods and Materials
Chapter 3 Wiring Methods and Materials
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
378.30 ARTICLE 382 - NONMETALLIC EXTENSIONS<br />
378.30 Securing <strong>and</strong> Supporting. Nonmetallic wireway<br />
shall be supported in accordance with 378.30(A) <strong>and</strong> (B).<br />
(A) Horizontal Support. Nonmetallic wireways shall be<br />
supported where run horizontally at intervals not to exceed<br />
900 mm (3 ft), <strong>and</strong> at each end or joint, unless listed for<br />
other support intervals. In no case shall the distance between<br />
supports exceed 3 m (10 ft).<br />
(D) Vertical Support. Vertical runs of nonmetallic wireway<br />
shall be securely supported at intervals not exceeding<br />
1.2 m (4 ft), unless listed for other support intervals, <strong>and</strong><br />
shall not have more than one joint between supports. Adjoining<br />
nonmetallic wireway sections shall be securely fastened<br />
together to provide a rigid joint.<br />
378.44 Expansion Fittings. Expansion fittings for nonmetallic<br />
wireway shall be provided to compensate for thermal<br />
expansion <strong>and</strong> contraction where the length change is expected<br />
to be 6 mm (0.25 in.) or greater in a straight run.<br />
FPN: See Table 352.44 for expansion characteristics of<br />
PVC conduit. The expansion characteristics of PVC nonmetallic<br />
wireway are identical.<br />
378.56 Splices <strong>and</strong> Taps. Splices <strong>and</strong> taps shall be permitted<br />
within a nonmetallic wireway, provided they are accessible.<br />
The conductors, including splices <strong>and</strong> taps, shall not<br />
fill the nonmetallic wireway to more than 75 percent of its<br />
area at that point.<br />
378.58 Dead Ends. Dead ends of nonmetallic wireway<br />
shall be closed using listed fittings.<br />
378.60 Grounding. Where equipment grounding is required,<br />
a separate equipment grounding conductor shall be<br />
installed in the nonmetallk wireway. A separate equipment<br />
grounding conductor shall not be required where the<br />
grounded conductor is used to ground equipment as permitted<br />
in 250.142.<br />
378.70 Extensions from Nonmetallic Wireways. Extensions<br />
from nonmetallic wireway shall be made with cord<br />
pendants or any wiring method of <strong>Chapter</strong> 3. A separate<br />
equipment grounding conductor shall be installed in, or an<br />
equipment grounding connection shall be made to, any of<br />
the wiring methods used for the extension.<br />
380.1 Scope. This article covers the use <strong>and</strong> installation<br />
requirements for multioutlet assemblies.<br />
380.2 Use.<br />
(A) Permitted. The use of a multioutlet assembly shall be<br />
permitted in dry locations.<br />
(D) Not Permitted. A multioutlet assembly shall not be<br />
installed as follows:<br />
(1) Where concealed, except that it shall be permissible to<br />
surround the back <strong>and</strong> sides of a metal multioutlet assembly<br />
by the building finish or recess a nonmetallic<br />
multioutlet assembly in a baseboard<br />
(2) Where subject to severe physical damage<br />
(3) Where the voltage is 300 volts or more between conductors<br />
unless the assembly is of metal having a thickness<br />
of not less than 1.02 mm (0.040 in.)<br />
(4) Where subject to corrosive vapors<br />
(5) In hoistways<br />
(6) In any hazardous (classified) location, except as permitted<br />
b,!.~r:~.~!~iUl~lil;:Col,~<br />
380.3 Metal Multioutlet Assembly Through Dry Partitions.<br />
It shall be permissible to extend a metal multioutlet<br />
assembly through (not run within) dry partitions if arrangements<br />
are made for removing the cap or cover on all exposed<br />
portions <strong>and</strong> no outlet is located within the partitions.<br />
I. General<br />
382.1 Scope. This article covers the use, installation, <strong>and</strong><br />
construction specifications for nonmetallic extensions.<br />
382.2 Definitions.<br />
III. Construction Specifications<br />
378.120 Marking. Nonmetallic wireways shall be marked<br />
so that the manufacturer's name or trademark <strong>and</strong> interior<br />
cross-sectional area in square inches shall be visible after<br />
installation. Marking for limited smoke shall be permitted<br />
on the nonmetallic wireways that have limited smokeproducing<br />
characteristics.<br />
~H~'<br />
Ot':otttm'