Seko Twindose 35 Series Inst.. - UK

More documents

Recommendations

Info

TWINDOSE 35 – System for dishwashers 2.5.3 Plumbing connections for the sanitizer pump (only on 3-pump systems). To install the sanitizer pump, proceed as follows: Suction • Insert the suction hose into the flat side of the stainless steel weight. • Insert the hose sticking out of the countersunk part of the stainless steel weight into the foot filter. • Secure the pipe by pushing the weight against the filter and rotating it until it matches perfectly (Figure 9). • Cut a sufficient length of sanitizer suction hose to reach the sanitizer pump. • Put the suction hose into the ring nut. • Insert the hose into the suction side of the sanitizer pump. • Tighten the fixing ring nut by hand on the suction side of the sanitizer pump. Stainless steel weight Fig. 9 Suction hose Foot filter Delivery • Insert the delivery hose into the fixing ring nut on the injection valve. • Fix the hose to the injection valve. • Cut a sufficient length of delivery hose to connect it between the delivery side of the sanitizer pump (right) and the injection valve. • Tighten the ring nuts on the injection valve and the pump by hand. Fig. 10 Always use the foot filter and make sure it reaches the bottom of the tank. Clean out any residue regularly. TWINDOSE 35 code 0000136655 rev. 1.0 14
TWINDOSE 35 – System for dishwashers 2.6 INSTALLING THE CONDUCTOMETRIC SENSOR IN THE TANK The probe detects the concentration of detergent. Correct positioning of the probe is essential for adequately checking of the concentration of detergent. Always use the new probe supplied with the TWINDOSE 35. The probe must be positioned where it is constantly immersed in the solution in the washing tank, in a position in which there is an adequate flow of the solution, and near the point at which the product enters. • Install the probe in the washing tank, below the water level. • If you are not able to find an existing hole, it may be advisable to use a 22.2 mm cutter or punch. • Always install the probe: o Far from the point at which the water enters the tank. o Near the circulation pump intake. o Far from corners, heating elements, or the bottom of the tank. • Remove the probe fixing nut. • Remove a rubber gasket and the plastic washer. • Insert the probe with the rubber gasket into the hole from the inside of the dishwasher tank. • Fit the rubber gasket and the washer. • Put on the nut and tighten it using a spanner if necessary. • Wire up the probe using a wire (not supplied) applying the colour coding and using the Faston clip and cap supplied, as shown in the instructions given in the diagram below. • Connect the wires from the terminals on the probe to terminals 21,22, and 24 on circuit board, connecting the colours as indicated in the figure and in enclosures A, B, and C. • For best results we recommend using a copper trefoil wire of 18 AWG for the probe connection. Do not lay the cable near high voltage AC lines. DISHWASHER SIDE WATER LEVEL FIXING NUT PROBE WASHER RUBBER GASKETS HOW TO CONNECT UP THE CONDUCTIVITY PROBE COME COLLEGARE LA SONDA CODUTTIVA FIT THE PROBE INSIDE THE TANK BEFORE FITTING THE CAP OVER THE FASTON CLIPS MONTARE LA SONDA IN VASCA PRIMA DI INSERIRE IL CAPPUCCIO SUI FASTON BLUE YELLOW-GREEN GIALLO/VERDE BROWN MARRONE BLUE YELLOW- GIALLO/VERDE GREEN BROWN MARRONE BLUE YELLOW- GIALLO/VERDE GREEN MARRONE BROWN WIRE NOT SUPPLIEDT YELLOW-GREEN GIALLO/VERDE MARRONE BROWN BLU BLUE 21 22 23 24 COND PROBE WARNING: ATTENZIONE!!! FORM ESEGUIRE THE CONNECTION IL COLLEGAMNETO AS SHOWN IN SECONDO THE DIAGRAM FIGURA To replace the probe, cut the wire immediately before the male Faston clip. TWINDOSE 35 code 0000136655 rev. 1.0 15
Page 1 and 2: TWINDOSE 35 - System for dishwasher
Page 13: TWINDOSE 35 - System for dishwasher

Seko Twindose 35 Series Inst.. - UK

Create successful ePaper yourself

Delete template?

Save as template?