condair FF2
condair FF2
condair FF2
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
32<br />
5.5 Electrical installation<br />
5.5.1 Wiring diagram Master units (stand-alone units)<br />
B2<br />
B1<br />
X1<br />
Y<br />
- +<br />
X2<br />
X8<br />
B3<br />
X3<br />
B5<br />
M<br />
3~<br />
φ<br />
B6<br />
GND<br />
Press<br />
F5<br />
P<br />
N<br />
P1<br />
X11<br />
GND<br />
Input+<br />
Input+<br />
200mAF<br />
S1<br />
F4<br />
X10<br />
1<br />
GND<br />
Out FC+<br />
24V<br />
5V<br />
L1 N L1 N<br />
4<br />
2 5<br />
Front Panel<br />
+24V<br />
Res1<br />
Res2<br />
Lev/Tp<br />
P min.<br />
+24V<br />
X9<br />
F1<br />
6.3AT<br />
L1<br />
N<br />
SC1<br />
SC2<br />
PT1<br />
PT2<br />
B7<br />
J<br />
Option<br />
Conductivity<br />
RS485 Master<br />
Slave System<br />
K1<br />
X<br />
B4<br />
X<br />
F3<br />
630mAT<br />
F2<br />
1AT<br />
Enable<br />
FC<br />
N<br />
N<br />
UV/Fan<br />
Drain Valve<br />
Inlet Valve<br />
JP3<br />
N<br />
Stage 3<br />
Stage 2<br />
Stage 1<br />
N<br />
Pump<br />
N<br />
HighP<br />
H<br />
Error<br />
X4<br />
X5<br />
Y1<br />
5 Y5<br />
3<br />
1<br />
X6<br />
Y6<br />
X7<br />
Service<br />
Steam<br />
Unit On<br />
V<br />
Y2<br />
Y4<br />
Y3<br />
K<br />
U V W B7 T1T2<br />
GND +<br />
B4 Drive Enable<br />
B2 +24V<br />
B5 Run forward<br />
T5<br />
T6<br />
Q<br />
F6<br />
L1 L2 L3<br />
L1 L2 L3 N<br />
3 x 400V<br />
L1 L2 L3 N PE<br />
U<br />
B1 Pressure transmitter 1...10V<br />
B2 Active humidity controller or humidity sensor<br />
B3 Minimum pressure switch (supply pressure)<br />
B4 Conductivity monitoring print (option)<br />
B5 Conductivity sensor (option)<br />
B6 Temperature sensor motor coil<br />
B7 Ventilator interlock<br />
F1 Fuse 6.3A, slow-acting (power supply control unit)<br />
F2 Fuse 1A, slow-acting (Relay 230V)<br />
F3 Fuse 630mA, quick-acting (step valves)<br />
F4 Fuse 200mA, quick-acting (analogue entry)<br />
F5 Fuse 200mA, quick-acting (24 VDC supply)<br />
F6 External fuse 10A, slow-acting (voltage supply 3x400V)<br />
H Remote operating and fault indication (option)<br />
J Cable bridge (must be removed, if B7 is connected)<br />
JP3 Jumper must be set, if Slave unit is connected<br />
K Main contactor<br />
K1 External safety chain (safety humidistat, flow control,<br />
ventilator interlock, etc.)<br />
M Motor high-pressure pump<br />
Q External service switch (min. contact clearance 3<br />
mm) or plug-type connector (installation mandatory)<br />
S1 Unit switch<br />
U Frequency converter pump motor<br />
V Ventilator pump motor<br />
X Bus connection Master-Slave systems<br />
Y1 Supply valve<br />
Y2 Flushing valve supply pressure<br />
Y3 Step valve 1/7<br />
Y4 Step valve 2/7<br />
Y5 Step valve 4/7<br />
Y6 Flushing valve working pressure (option)
Change language