Tutorial.pdf

More documents

Recommendations

Info

Changing parameter modes: arithmetic expressions Each parameter can have three modes: Normal, Sweep and Script. Script mode allows the user to enter arithmetic expressions and also access parameters defined globally. • In the CW Laser, click on the property Mode. • From the drop down menu, select Script mode. • In the parameter Value, enter the expression ‘193.1+0.1’ • Click on Verify Script button You will see the value of the script expression in the message list in the dialog box and the results will be 193.2. Figure 15 -Using arithmetic expressions 10
Visualizers parameters In order to access the parameter of the Visualizer you must select the icon and right click on it, since double clicking on any of the visualizers will bring up a dialog box for visualization of the graphs and results generated during the simulation instead the parameters. • In the layout editor, select the Optical Spectrum Analyzer icon. • Right click on it, it will appear a pop up menu. • From the pop up menu, select “Component properties”. Running the simulation Figure 16 -Accessing visualizers parameters OptiSys_Design allows the user to control the calculation in different ways: • Calculate the whole project: multiple design versions will all sweep iterations. • Calculate the current design version: all sweep iterations. • Calculate current iteration: current sweep iteration in the current design version. By default we will calculate the whole project, since we do not have multiple design versions and no sweep iterations. • File Menu select Calculate : 11
Page 1: Tutorials OptiSys_Design Optical Co
Page 5 and 6: TABLE OF CONTENTS INTRODUCTION.....
Page 7 and 8: Introduction The most efficient way
Page 9 and 10: • Select CW Laser 1.0 and place i
Page 11 and 12: • The CW laser output to the Mach
Page 13 and 14: Visualizers and Data Monitors Figur
Page 15: For each category tab, there is a l
Page 19 and 20: Optical Spectrum Analyzer Optical s
Page 21 and 22: You can also trace the to obtain th
Page 23 and 24: Lesson 2: Subsystems - Hierarchical
Page 25 and 26: Closing the subsystem Main layout S
Page 27 and 28: Subsystem properties: name and icon
Page 29 and 30: • In the Add parameter dialog box
Page 31 and 32: Global parameter frequency Global p
Page 33 and 34: Figure 39 -Adding components to the
Page 35 and 36: Running the simulation You can conn
Page 37 and 38: • Resize the layout by pressing C
Page 39 and 40: Parameter groups table gives you ac
Page 41 and 42: Figure 49 -Simulation results from
Page 43 and 44: Figure 52 -Loop control parameters
Page 45 and 46: • Select Electrical Amplifier 1.0
Page 47 and 48: Figure 57 -BER Analyzer graphs You
Page 49 and 50: The 3D graph is available in the gr
Page 51 and 52: Selecting the parameter to be itera
Page 53 and 54: Changing the values of sweep iterat
Page 55 and 56: Getting results using the Graph bui
Page 57 and 58: Browsing parameter sweep iterations
Page 59 and 60: Lesson 5: Design Versions - EDFA Ch
Page 61 and 62: Lesson 6: Optimizations - System ma
Page 63 and 64: Figure 77 -Getting results 57
Page 65 and 66: Figure 79 -Parameters for fiber len
Page 67 and 68:
Input After SMF Output Figure 82 -S
Page 69 and 70:
Figure 84 -The dispersion compensat
Page 71 and 72:
Lesson 9: Design of a broadband Ram
Page 73 and 74:
After creating the subsystem as sho
Page 75 and 76:
Figure 91 - Raman Amplifier subsyst
Page 77 and 78:
Figure 93 - Forward output spectrum
Page 79 and 80:
Lesson 10: Optimization of the gain
Page 81 and 82:
It is immediately seen that optimal
show all

Tutorial.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?