Tutorial.pdf

More documents

Recommendations

Info

Creating sub folders in the Custom Library In order to add the External Modulated Transmitter to the Custom library we will create a new folder named “Transmitters”. • Select the Custom folder in the component library, • Right click in the background of the custom library, • In the pop up menu, select “Add Folder…” • In the New Folder dialog box, enter “Transmitters” in the edit box, • Press the OK button. In the Custom folder in the Component library a new folder named “Transmitters” will appear. Figure 38 -Creating folders in the component library Adding the component to the library You can drag and drop components to any folder in the Custom library. We will add the External Modulated Transmitter to the Custom/Transmitters library. • Select the Transmitters folder from the custom library, • In the layout editor, select the External Modulated Transmitter component, • Drag the External Modulated Transmitter and drop it in the Transmitters folder. The subsystem icon will be created with the component name: External Modulated Transmitter. 26
Figure 39 -Adding components to the component library Creating additional ports In order to access the electrical signal from the NRZ Pulse Generator inside of the External Modulated Transmitter we can create an additional output port in the subsystem. • Look inside of the External Modulated Transmitter, • Create a new output port in the subsystem, Figure 40 -Adding a new output port to the subsystem However we cannot connect the Pulse Generator output to this port because it’s already connected to the Mach-Zehnder Modulator input. To solve this problem we can duplicate the signal from the Pulse Generator and connect it to both ports: Mach-Zehnder Modulator input and Subsystem output. 27
Page 1: Tutorials OptiSys_Design Optical Co
Page 5 and 6: TABLE OF CONTENTS INTRODUCTION.....
Page 7 and 8: Introduction The most efficient way
Page 9 and 10: • Select CW Laser 1.0 and place i
Page 11 and 12: • The CW laser output to the Mach
Page 13 and 14: Visualizers and Data Monitors Figur
Page 15 and 16: For each category tab, there is a l
Page 17 and 18: Visualizers parameters In order to
Page 19 and 20: Optical Spectrum Analyzer Optical s
Page 21 and 22: You can also trace the to obtain th
Page 23 and 24: Lesson 2: Subsystems - Hierarchical
Page 25 and 26: Closing the subsystem Main layout S
Page 27 and 28: Subsystem properties: name and icon
Page 29 and 30: • In the Add parameter dialog box
Page 31: Global parameter frequency Global p
Page 35 and 36: Running the simulation You can conn
Page 37 and 38: • Resize the layout by pressing C
Page 39 and 40: Parameter groups table gives you ac
Page 41 and 42: Figure 49 -Simulation results from
Page 43 and 44: Figure 52 -Loop control parameters
Page 45 and 46: • Select Electrical Amplifier 1.0
Page 47 and 48: Figure 57 -BER Analyzer graphs You
Page 49 and 50: The 3D graph is available in the gr
Page 51 and 52: Selecting the parameter to be itera
Page 53 and 54: Changing the values of sweep iterat
Page 55 and 56: Getting results using the Graph bui
Page 57 and 58: Browsing parameter sweep iterations
Page 59 and 60: Lesson 5: Design Versions - EDFA Ch
Page 61 and 62: Lesson 6: Optimizations - System ma
Page 63 and 64: Figure 77 -Getting results 57
Page 65 and 66: Figure 79 -Parameters for fiber len
Page 67 and 68: Input After SMF Output Figure 82 -S
Page 69 and 70: Figure 84 -The dispersion compensat
Page 71 and 72: Lesson 9: Design of a broadband Ram
Page 73 and 74: After creating the subsystem as sho
Page 75 and 76: Figure 91 - Raman Amplifier subsyst
Page 77 and 78: Figure 93 - Forward output spectrum
Page 79 and 80: Lesson 10: Optimization of the gain
Page 81 and 82: It is immediately seen that optimal

Tutorial.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?