Tutorial.pdf

More documents

Recommendations

Info

A subsystem icon will replace the components. Observe that the visualizers that are not included in the selection will be disconnected. This is because the subsystem will not add additional ports to connect the visualizers. Figure 26 -Creating a subsystem. Looking inside of the subsystem • Select the subsystem icon, • Right click over the selection, • From the pop up menu, select Look inside Observe that a new tab was added to the layout tab, now you can change parameters and create ports in order to access the signals from the subsystem. Figure 27 -Looking inside of the subsystem To go back to the main system, you can close the subsystem by right clicking in the layout background and then selecting Close Subsystem, or you can click in the Main layout tab in and keep the subsystem opened. 18
Closing the subsystem Main layout Subsystem Figure 28 -Closing subsystems Creating output ports • In the layout tools toolbar, select Draw Output Port Tool, • Position the cursor near to the document border, left click on it, • Connect the Mach-Zehnder modulator output to the subsystem port. The port was created, if you go back to the Main layout there will be an output port in the subsystem icon. In order to create input ports use the same procedure. Since this is a transmitter, in this example we will not create input ports. 19
Page 1: Tutorials OptiSys_Design Optical Co
Page 5 and 6: TABLE OF CONTENTS INTRODUCTION.....
Page 7 and 8: Introduction The most efficient way
Page 9 and 10: • Select CW Laser 1.0 and place i
Page 11 and 12: • The CW laser output to the Mach
Page 13 and 14: Visualizers and Data Monitors Figur
Page 15 and 16: For each category tab, there is a l
Page 17 and 18: Visualizers parameters In order to
Page 19 and 20: Optical Spectrum Analyzer Optical s
Page 21 and 22: You can also trace the to obtain th
Page 23: Lesson 2: Subsystems - Hierarchical
Page 27 and 28: Subsystem properties: name and icon
Page 29 and 30: • In the Add parameter dialog box
Page 31 and 32: Global parameter frequency Global p
Page 33 and 34: Figure 39 -Adding components to the
Page 35 and 36: Running the simulation You can conn
Page 37 and 38: • Resize the layout by pressing C
Page 39 and 40: Parameter groups table gives you ac
Page 41 and 42: Figure 49 -Simulation results from
Page 43 and 44: Figure 52 -Loop control parameters
Page 45 and 46: • Select Electrical Amplifier 1.0
Page 47 and 48: Figure 57 -BER Analyzer graphs You
Page 49 and 50: The 3D graph is available in the gr
Page 51 and 52: Selecting the parameter to be itera
Page 53 and 54: Changing the values of sweep iterat
Page 55 and 56: Getting results using the Graph bui
Page 57 and 58: Browsing parameter sweep iterations
Page 59 and 60: Lesson 5: Design Versions - EDFA Ch
Page 61 and 62: Lesson 6: Optimizations - System ma
Page 63 and 64: Figure 77 -Getting results 57
Page 65 and 66: Figure 79 -Parameters for fiber len
Page 67 and 68: Input After SMF Output Figure 82 -S
Page 69 and 70: Figure 84 -The dispersion compensat
Page 71 and 72: Lesson 9: Design of a broadband Ram
Page 73 and 74: After creating the subsystem as sho
Page 75 and 76:
Figure 91 - Raman Amplifier subsyst
Page 77 and 78:
Figure 93 - Forward output spectrum
Page 79 and 80:
Lesson 10: Optimization of the gain
Page 81 and 82:
It is immediately seen that optimal
show all

Tutorial.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?