Tutorial.pdf

More documents

Recommendations

Info

• Go to the Project Browser (Ctrl+2), • Select the Graphs tab, • In the Graphs tab, select the BER Analyzer 1.0 in the tree, • Select the Q Factor graph, • Right click on it, then select Add to view or Quick view Observe that you will obtain a display with the graphs for all sweep iterations, one for each value of input power. These steps are described in Figure 70: Figure 70 -Combining graphs from different sweep iterations in one graph 52
Lesson 5: Design Versions – EDFA Characterization The sample file “EDFA Characterization.osd” shows how to use OptiSys_Design with multiple design versions. In this example we characterize the Erbium Doped Fiber Amplifier by using sweeps for the input parameters of the amplifier. Figure 71 -EDFA Characterization.osd This example use different parameter sweeps for each design version: • Length: Iterations of EDFA fiber length from 1 to 20 meters. • Input Signal Power: Iterations of CW laser signal power from -40 to 0 dBm • Pump Power: Iterations of Pump laser power from 10 to 200 mW • Wavelength: Iterations of CW laser signal wavelength from 1525 to 1600 nm Figure 72 -EDFA Multiple design versions and parameter sweeps 53
Page 1:
Tutorials OptiSys_Design Optical Co
Page 5 and 6:
TABLE OF CONTENTS INTRODUCTION.....
Page 7 and 8: Introduction The most efficient way
Page 9 and 10: • Select CW Laser 1.0 and place i
Page 11 and 12: • The CW laser output to the Mach
Page 13 and 14: Visualizers and Data Monitors Figur
Page 15 and 16: For each category tab, there is a l
Page 17 and 18: Visualizers parameters In order to
Page 19 and 20: Optical Spectrum Analyzer Optical s
Page 21 and 22: You can also trace the to obtain th
Page 23 and 24: Lesson 2: Subsystems - Hierarchical
Page 25 and 26: Closing the subsystem Main layout S
Page 27 and 28: Subsystem properties: name and icon
Page 29 and 30: • In the Add parameter dialog box
Page 31 and 32: Global parameter frequency Global p
Page 33 and 34: Figure 39 -Adding components to the
Page 35 and 36: Running the simulation You can conn
Page 37 and 38: • Resize the layout by pressing C
Page 39 and 40: Parameter groups table gives you ac
Page 41 and 42: Figure 49 -Simulation results from
Page 43 and 44: Figure 52 -Loop control parameters
Page 45 and 46: • Select Electrical Amplifier 1.0
Page 47 and 48: Figure 57 -BER Analyzer graphs You
Page 49 and 50: The 3D graph is available in the gr
Page 51 and 52: Selecting the parameter to be itera
Page 53 and 54: Changing the values of sweep iterat
Page 55 and 56: Getting results using the Graph bui
Page 57: Browsing parameter sweep iterations
Page 61 and 62: Lesson 6: Optimizations - System ma
Page 63 and 64: Figure 77 -Getting results 57
Page 65 and 66: Figure 79 -Parameters for fiber len
Page 67 and 68: Input After SMF Output Figure 82 -S
Page 69 and 70: Figure 84 -The dispersion compensat
Page 71 and 72: Lesson 9: Design of a broadband Ram
Page 73 and 74: After creating the subsystem as sho
Page 75 and 76: Figure 91 - Raman Amplifier subsyst
Page 77 and 78: Figure 93 - Forward output spectrum
Page 79 and 80: Lesson 10: Optimization of the gain
Page 81 and 82: It is immediately seen that optimal
show all

Tutorial.pdf

Create successful ePaper yourself

Delete template?

Save as template?