ParSec Data Display & Entry Panel (DDE ... - How do I

More documents

Recommendations

Info

4.4.7 Change PIN numbers. This facility is provided to change the PIN codes of Levels 0, 1, 2 & 3. Re-entry invalid 2345 Accept or time out 4 change pins 6 access level 0, 1, 2 or 3 Accept enter new pin 1234 Accept 1234 Accept Re-enter new pin 29-Mar-00 10:31 Monitoring 3333 Accept 2 8 status v2.2 p-y s-y a-y t=006 Change PINs Note. 1. PIN codes must be a four-digit code. DDE Installation & Operation Manual - Issue: 5 August 2000 - Page 32
5 Commissioning the System 5.1 Power Up When power is initially applied to the DDE panel the display will read Configuration Reset If you now press the ACCEPT key, the DDE will display:- DD/MMM/YY HH/MM MONITORING Notes • If key 2 is depressed and held down before power is applied, the DDE will perform a self-test routine (see section 6.1). • If it is not practicable to switch off the mains power to perform the self test, you can press the DDE master reset button on the main processor PCB ref. S2. • If the configuration is detected as corrupt at power-on, a Configuration reset Message is displayed, the configuration is reset to system defaults, and the tag table is cleared (see section 5.2). No time-out applies to this message. 5.2 Default SAT Pulse Count The default SAT pulse count (see System Options, Section 4.4.3) must be set before SAT's are acquired; if the setting is changed during normal use of the DDE, the change will only be applied to SAT's acquired after the change is made. Note that the pulse count settings for individual SAT's as described in section 4.4.2 will default to the global SAT pulse count DDE Installation & Operation Manual - Issue: 5 August 2000 - Page 33
Page 1 and 2: ParSec Data Display & Entry Panel (
Page 3 and 4: ParSec Data Display & Entry Panel (
Page 5 and 6: CONTENTS 1 Caution - Static Precaut
Page 7 and 8: 1 CAUTION- STATIC PRECAUTIONS Some
Page 9 and 10: Design The DDE consists of a hinged
Page 11 and 12: 2.4 Communications Interface Commun
Page 13 and 14: 3 INSTALLING THE DDE 3.1 Fixing the
Page 15 and 16: Term 2-6 (0V) Term 2-6 (0V) Term 2-
Page 17 and 18: This page is intentionally blank DD
Page 19 and 20: Loop individual conductors Screened
Page 21 and 22: 4 DDE OPERATION General Notes & Con
Page 23 and 24: 4.2 PIN Level 1 - Disable PAT's [Us
Page 25 and 26: 4.4 PIN Level 3 - Administration Le
Page 27 and 28: 4.4.1 PAT Options This function ena
Page 29 and 30: The following table illustrates how
Page 31 and 32: 4.4.4 Reset Options This function c
Page 33: 4.4.6 Alarm Options Facilities are
Page 37 and 38: 8. Change PIN numbers if required 9
Page 39 and 40: 6 TROUBLESHOOTING 6.1 System Self-t
Page 41 and 42: 7. Repair If for any reason you wis
Page 43 and 44: 8. Technical Specification 8.1 Dime
Page 45 and 46: 9. Change Record Issue Change Date

ParSec Data Display & Entry Panel (DDE ... - How do I

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?