Electronic Relays, Relay, HMI, Control, PLCs ... - Moeller Electric Parts

More documents

Recommendations

Info

easy MFD 4/60 Technical Data I/O modules MFD-… Moeller HPL0211-2007/2008 http://catalog.moeller.net MFD-R16 MFD-RA17 MFD-T16 MFD-TA17 MFD-T.P.. MFD-AC-R16 Digital inputs 24 V DC Number 12 12 6 Inputs can be used as analog inputs Potential isolation 4 (I7, I8, I11, I12) 4 (I7, I8, I11, I12) 2 (I11, I12) From power supply No No No Between digital inputs No No No From the outputs Yes Yes Yes From the PC interface, memory card NET network, EASY-Link Yes Yes Yes Rated operational voltage Ue V DC 24 24 24 On 0 signal Ue V DC < 5.0 (I1 – I6, I9 – I10), < 8 (I7, I8, I11, I12) On 1 signal Ue V DC > 15.0 (I1 – I6, I9 – I10), > 8.0 (I7, I8, I11, I12) < 5.0 (I1 – I6, I9 – I10), < 8 (I7, I8, I11, I12) > 15.0 (I1 – I6, I9 – I10), > 8.0 (I7, I8, I11, I12) < 5.0 (I1 – I4), < 8.0 (I11, I12) >15.0 (I1 – I4), > 8.0 (I11, I12) Input current on 1 signal I1 to I6 mA 3.3 (at 24 V DC) 3.3 (at 24 V DC) I1 to I4 mA 3.3 (at 24 V DC) I7, I8 mA 2.2 (at 24 V DC) 2.2 (at 24 V DC) I9, I10 mA 3.3 (at 24 V DC) 3.3 (at 24 V DC) I11, I12 mA 2.2 (at 24 V DC) 2.2 (at 24 V DC) 2.2 (at 24 V DC) Delay time from 0 to 1 Debounce ON ms 20 20 20 Debounce OFF ms Normally 0.025 (I1 – I4), normally 0.25 (I5, I6, I9, I10), normally 0.15 (I7, I8, I11, Normally 0.025 (I1 – I4), normally 0.25 (I5, I6, I9, I10), normally 0.15 (I7, I8, I11, Delay time from 1 to 0 Debounce ON ms 20 20 20 Debounce OFF ms Normally 0.025 (I1 – I4), normally 0.25 (I5, I6, I9, I10), normally 0.15 (I7, I8, I11, Normally 0.025 (I1 – I4), normally 0.25 (I5, I6, I9, I10), normally 0.15 (I7, I8, I11, Normally 0.1 (I1 – I4), normally 0.25 (I11 – I12) Normally 0.1 (I1 – I4), normally 0.2 (I11, I12) Cable length (unscreened) Frequency counter m 100 100 100 Quantity 4 (I1, I2, I3, I4) 4 (I1, I2, I3, I4) 4 (I1, I2, I3, I4) Counter frequency kHz < 3 < 3 < 3 Pulse shape Incremental counter Square Square Square Quantity 2 (I1 + I2, I3 + I4) 2 (I1 + I2, I3 + I4) 2 (I1 + I2, I3 + I4) Counter frequency kHz F 3 F 3 F 3 Pulse shape Square Square Square Signal offset Rapid counter inputs 90° 90° 90° Number 4 (I1, I2, I3, I4) 4 (I1, I2, I3, I4) 4 (I1, I2, I3, I4) Counter frequency kHz < 3 < 3 < 3 Pulse shape Square Square Square Cable length, screened Digital inputs 115/230 V AC m < 20 < 20 < 20 Number 12 Status indication Potential isolation LCD-display (if present) From power supply No Between digital inputs No From the outputs Yes From the PC interface, memory card NET network, EASY- Link Rated voltage L (sinusoidal) Yes On 0 signal V AC 0 – 40 On 1 signal V AC 79 – 264 Rated frequency Input current on 1 signal Hz 50 – 60 I1 - I12 mA 12 x 0.2 (at 115 V Delay time AC, 60 Hz), 12 x 0.5 (at 230 V AC, 50 Hz) Delay time (0 – 1x1 – 0) I1 – I12, 50x60 Hz Max. admissible cable length (per input) 10x100 I1 - I12 m Normally 60 For Moeller Electric Sales and Support call KMparts.com (866) 595-9616
http://catalog.moeller.net Moeller HPL0211-2007/2008 MFD-R16 MFD-T16 MFD-R… MFD-T… MFD-T(A)P Analog inputs Number Electrical isolation 4 (I7, I8, I11, I12) 2 (I11, I12) for MFD- T(A)P To power supply No From the digital inputs No To the outputs Yes From the PC interface, memory card, NET network, EASY-Link Yes Input type DC voltage Signal range V DC 0 – 10 Resolution, analog V 0.01 Resolution, digital V 0.01 Resolution Bit 10 (value 0 – 1023) Input impedance Accuracy of actual value kO 11.2 2 MFD devices % g 3 Within a single device % g 2 Conversion time, analog/digital ms Every CPU cycle Input current mA < 1 Cable length screened m < 30 Technical data I/O modules MFD-RA17 MFD-TA17 MFD-TAP Analog outputs Number Electrical isolation 1 1 To power supply No No From the digital inputs No No From the digital outputs Yes Yes From the PC interface, memory card, NET network, EASY-Link Yes Yes Output type DC voltage DC voltage Signal range V DC 0 – 10 0 – 10 Max. output current A 0.01 0.01 Load resistance 1 kO 1 kO Overload and short-circuit protection Yes Yes Resolution, analog V DC 0.01 0.01 Resolution, digital Bit 10, (value: 0 – 12 (value 0…4095) 1023) at QA01, MD Resolution, digital V DC – 0.1, 0.01, 0.001 at MD Recovery time ms 100 100 Accuracy -25 °C – 55 °C % 2 2 25°C % 1 1 Conversion time Every CPU cycle Every CPU cycle MFD-TP, MFD-TAP Analog input temperature resistance Pt100 or Ni1000 sensors Number Input type resistance sensor Platinum sensor Pt100 according to DIN EN 60751, IEC 751 Nickel sensor Ni1000 according to DIN 43760 Temperature range 2 x Pt100 or 2 x Nt1000 (jaccording to type) Pt100, Range A, selectable °C , (°F) –40 to +90, (-40 to 194); 0 to 250, (32 to 482); 0 to 400, (32 to 752) Ni1000, Range A, selectable °C , (°F) –40 to +90, (-40 to 194); 0 to 250, (32 to 482) Pt100, Range B Electrical isolation °C , (°F) 0 to 850, (32 to 1562); - 200 to 200, (–328 to 392) To power supply No From the digital inputs No To the outputs Yes From the PC interface, memory card, NET network, EASY-Link Resolution digital, scaling per sensor Yes With operands "IA" and "MD", selectable under scaling Bit 12 (0 to 4095) With operand "MD", selectable under scaling °C, (°F) 1, 0.1, (1), (0.1) Measuement value resolution analog/digital Bit Depending upon the scaling Measuring current mA < 1.6 Damage limit (in the case of a wiring error) Apply external voltage Measurement method Accuracy (without EMC interference) Two or three wire per sensor, selectable by connection of sensor Two MFD devices one above the other % Typically 1; maximal 1.6 (Pt); 1.2 (Ni) Pt100-sensor (Offset error, linearity error, repetition accuracy, temperature dependency of the device included) % g0.8 of measurement range Ni1000-sensor (Offsetf error, linearity error, repetition accuracy, temperature dependency of the device include) Conversion time, analog/digital % g0.6 of measurement range Without sampling time setting, selectable per sensor ms 200 With sampling time (adjustable), selectable per sensor Additional measurement aids ms 200 to 65535 Filterung (Software), smoothing of analog input signals (PT1 behaviour), only with set sampling time, selectable per sensor Yes . Filter for the suppression of certain frequencies and their multiples Diagnostics Hz 50, 60, 250, 500 Card diagnostic Yes Wire break diagnostic per sensor Yes Wire break diagnostic per sensor Yes Below lower measurement range Yes Above upper measurement range Yes Cable length screened m < 10 MFD... For Moeller Electric Sales and Support call KMparts.com (866) 595-9616 4/61 easy MFD
Page 1 and 2:
Electronic Relays, Relay, HMI, Cont
Page 3 and 4:
http://catalog.moeller.net Moeller
Page 5 and 6:
Electronic relays 4/6 Applications
Page 7 and 8: Electronic relays 4/8 Ordering Meas
Page 9 and 10: Electronic relays 4/10 Ordering mea
Page 11 and 12: Electronic relays 4/12 Engineering
Page 13 and 14: http://catalog.moeller.net Moeller
Page 57: http://catalog.moeller.net Moeller
Page 61 and 62: easy relay, easy MFD, easy Control
Page 83 and 84: System overview http://catalog.moel
Page 97 and 98: Description http://catalog.moeller.
Page 99 and 100: HMI MI4 4/104 Application Descripti
Page 101 and 102: Switched-mode power supply units, p
Page 103 and 104: Modular PLC - XC100/XC200 4/108 Tec
Page 109 and 110:
Modular PLC - XC100/XC200 4/114 Tec
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Compact PLC PS4 4/120 Technical Dat
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Switched-mode power supply units, p
Page 145 and 146:
Page 147 and 148:
show all

Electronic Relays, Relay, HMI, Control, PLCs ... - Moeller Electric Parts

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?