Electronic Relays, Relay, HMI, Control, PLCs ... - Moeller Electric Parts

http://catalog.moeller.net Moeller HPL0211-2007/2008
MFD-R16
MFD-T16
MFD-R…
MFD-T…
MFD-T(A)P
Analog inputs
Number
Electrical isolation
4 (I7, I8, I11, I12)
2 (I11, I12) for MFD-
T(A)P
To power supply No
From the digital inputs No
To the outputs Yes
From the PC interface, memory card, NET network,
EASY-Link
Yes
Input type DC voltage
Signal range V DC 0 – 10
Resolution, analog V 0.01
Resolution, digital V 0.01
Resolution Bit 10
(value 0 – 1023)
Input impedance
Accuracy of actual value
kO 11.2
2 MFD devices % g 3
Within a single device % g 2
Conversion time, analog/digital ms Every CPU cycle
Input current mA < 1
Cable length screened m < 30
Technical data
I/O modules
MFD-RA17
MFD-TA17
MFD-TAP
Analog outputs
Number
Electrical isolation
1 1
To power supply No No
From the digital inputs No No
From the digital outputs Yes Yes
From the PC interface, memory card,
NET network, EASY-Link
Yes Yes
Output type DC voltage DC voltage
Signal range V DC 0 – 10 0 – 10
Max. output current A 0.01 0.01
Load resistance 1 kO 1 kO
Overload and short-circuit protection Yes Yes
Resolution, analog V DC 0.01 0.01
Resolution, digital Bit 10, (value: 0 – 12 (value 0…4095)
1023)
at QA01, MD
Resolution, digital V DC – 0.1, 0.01, 0.001 at
MD
Recovery time ms 100 100
Accuracy
-25 °C – 55 °C % 2 2
25°C % 1 1
Conversion time Every CPU cycle Every CPU cycle
MFD-TP, MFD-TAP
Analog input temperature resistance Pt100 or Ni1000 sensors
Number
Input type resistance sensor
Platinum sensor Pt100 according to DIN EN 60751, IEC 751
Nickel sensor Ni1000 according to DIN 43760
Temperature range
2 x Pt100 or 2 x Nt1000 (jaccording to type)
Pt100, Range A, selectable °C , (°F) –40 to +90, (-40 to 194); 0 to 250, (32 to 482); 0 to 400, (32 to 752)
Ni1000, Range A, selectable °C , (°F) –40 to +90, (-40 to 194); 0 to 250, (32 to 482)
Pt100, Range B
Electrical isolation
°C , (°F) 0 to 850, (32 to 1562); - 200 to 200, (–328 to 392)
To power supply No
From the digital inputs No
To the outputs Yes
From the PC interface, memory card, NET network, EASY-Link
Resolution digital, scaling per sensor
Yes
With operands "IA" and "MD", selectable under scaling Bit 12 (0 to 4095)
With operand "MD", selectable under scaling °C, (°F) 1, 0.1, (1), (0.1)
Measuement value resolution analog/digital Bit Depending upon the scaling
Measuring current mA < 1.6
Damage limit (in the case of a wiring error) Apply external voltage
Measurement method
Accuracy (without EMC interference)
Two or three wire per sensor, selectable by connection of sensor
Two MFD devices one above the other % Typically 1; maximal 1.6 (Pt); 1.2 (Ni)
Pt100-sensor (Offset error, linearity error, repetition accuracy, temperature
dependency of the device included)
% g0.8 of measurement range
Ni1000-sensor (Offsetf error, linearity error, repetition accuracy, temperature
dependency of the device include)
Conversion time, analog/digital
% g0.6 of measurement range
Without sampling time setting, selectable per sensor ms 200
With sampling time (adjustable), selectable per sensor
Additional measurement aids
ms 200 to 65535
Filterung (Software), smoothing of analog input signals
(PT1 behaviour), only with set sampling time, selectable per sensor
Yes
. Filter for the suppression of certain frequencies and their multiples
Diagnostics
Hz 50, 60, 250, 500
Card diagnostic Yes
Wire break diagnostic per sensor Yes
Wire break diagnostic per sensor Yes
Below lower measurement range Yes
Above upper measurement range Yes
Cable length screened m < 10
MFD...
For Moeller Electric Sales and Support call KMparts.com (866) 595-9616
4/61
easy MFD