FS1575_2575_5075 Installation Manual E1 6-15-2012 - Furuno USA

More documents

Recommendations

Info

1. HOW TO INSTALL THE SYSTEM Outdoor installation • The coupler is water-jetsproof, but is not designed to take a continual soaking. If necessary, cover the top and sides with a wooden housing (or similar enclosure) or by sealing any opening in the top or sides with silicone sealant. • Keep wires as short as possible and keep the wires away from any grounded conductors such as lifelines, mast shrouds, or fittings. • Locate the insulator away from funnels, etc. 1.2.2 Ground CAUTION Ground the equipment. Ungrounded equipment can give off or receive electromagnetic interference or cause electrical shock. The ground connection must have the lowest possible RF-impedance. Losses in the ground connection reduce the communication distance. Make the ground connection to the Antenna Coupler with a copper strap, constructed as shown below. For vessels with conducting hulls, make the width at least 60 mm and the length not more than one meter. For FRP vessels, make the width at least 60 mm and the length not more than five meters. Connect to the ground termnaml of the antenna coupler. Copper strap Ground plate (a piece of steel plate) Solder For outdoor installation, apply a coat of marine paint to prevent corrosion. For outdoor installation, do the following. Braze Weld to ship's structure • Coat the junction where the copper strap connects to the ground terminal of the antenna coupler with silicone sealant. • Coat the copper strap between the ground plate and ground terminal of the anntenna coupler with marine paint to prevent corrosion. • Add a supplemental ground wire (local supply, more than 14 sq) and fasten it to the ground terminal of the antenna coupler as shown below. Ground terminal of the antenna coupler. Copper strap Fasten the supplemental ground wire (more than 14 sq). 4
1. HOW TO INSTALL THE SYSTEM 1.2.3 Installation procedure Outdoor installation Fasten the Antenna Coupler to a bulkhead of the bridge, mast, handrail, etc., with the M6 bolts (local supply). For installation on the mast, see section 1.5 to select a location. Weld suitable mounting fixtures (local supply) to the mast and bolt the coupler there. Fix with four M6 bolts (local supply). Mounting fixture (Local supply) Indoor installation Pictured: AT-5075 DO NOT install coupler horizontally. Fasten the Antenna Coupler to a bulkhead on the bridge or the overhead. Select a location where the distance between the lead-in insulator and the coupler is as short as possible. Lead-in insulator Antenna switch Installation on the overhead Stand-off insulator From antenna selection switch Installation on a bulkhead 5
Page 1 and 2: Installation Manual SSB RADIOTELEPH
Page 3 and 4: SAFETY INSTRUCTIONS The installer m
Page 5 and 6: SYSTEM CONFIGURATION * 3 For DSC ro
Page 7 and 8: EQUIPMENT LIST Name Type Code No. R
Page 9 and 10: 1. HOW TO INSTALL THE SYSTEM 1.1 Co
Page 11: 1. HOW TO INSTALL THE SYSTEM 1.2 An
Page 15 and 16: 1. HOW TO INSTALL THE SYSTEM 1.5 An
Page 17 and 18: 1. HOW TO INSTALL THE SYSTEM 1.6.5
Page 19 and 20: 1. HOW TO INSTALL THE SYSTEM 3. Fas
Page 21 and 22: 1. HOW TO INSTALL THE SYSTEM 1.6.10
Page 23 and 24: Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Page 25 and 26: Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Page 27 and 28: 2. WIRING 4. Connect the signal cab
Page 29 and 30: 2. WIRING 2.1.2 Connections for out
Page 31 and 32: 2. WIRING Locking wire saddle Cable
Page 33 and 34: 2. WIRING 2.3 Control Unit Connect
Page 35 and 36: 2. WIRING MIF unit Use connector 17
Page 37 and 38: 2. WIRING 110 110 100 100 100V 10%
Page 39 and 40: 2. WIRING 2.6 Automatic Antenna Swi
Page 41 and 42: 3. INITIAL SETTINGS 2. Enter the pa
Page 43 and 44: 3. INITIAL SETTINGS 3.4.3 DSC SETUP
Page 45 and 46: 3. INITIAL SETTINGS DIVIDER: Divide
Page 47 and 48: 3. INITIAL SETTINGS TX PWR (TUNE) x
Page 49 and 50: 3. INITIAL SETTINGS Standard config
Page 51 and 52: 3. INITIAL SETTINGS Full duplex con
Page 53 and 54: APPENDIX 1 JIS CABLE GUIDE Cables l
Page 55 and 56: A-3
Page 57 and 58: A-7
Page 59 and 60: A-11
Page 61 and 62: A-15
Page 63:
D-2
Page 66 and 67:
D-4
Page 70 and 71:
D-6
Page 72 and 73:
D-8
Page 74 and 75:
D-10
Page 76 and 77:
D-12
Page 78 and 79:
D-14
Page 82 and 83:
D-16
Page 84 and 85:
D-18
Page 86 and 87:
2 3 4 5 6 A B C D *2 MJ-A3SPF0023 -
show all

FS1575_2575_5075 Installation Manual E1 6-15-2012 - Furuno USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?