FS1575_2575_5075 Installation Manual E1 6-15-2012 - Furuno USA

More documents

Recommendations

Info

3. INITIAL SETTINGS Shared antenna configuration 2: R_ANT and WR2 antennas commonly shared Optional WR2 Board installed to watch on DSC general frequencies. 1) Turn on [DIVIDER] in the [RT SETUP] menu. 2) Set [RX ANT] on the [RT SETUP] menu to [CONNECT]. 3) Use the mini-pin assemblies (supplied) to make these connections: • Connect J4 to J5 on the RX FIL Board. • Connect J6 on RX FIL Board to J2 on WR1 Board. RANT T/R ANT AT-5075/ AT-1575 WR1 ANT J3 J2 J5 J6 J2 J1 J3 J4 J7 J2 J2 42
3. INITIAL SETTINGS Full duplex configurations (FS-5075 only) Full duplex configuration 1: Separate R_ANT and WR1 antennas, optional DUP-FIL board installed Watch on DSC general frequencies available with installation of optional WR2 Board. Set [RX ANT] on the [RT SETUP] menu in the [SERVICE] menu to [CONNECT]. R_ANT T/R_ANT T/R_ANT J1 J2 J3 J3 J8 R_ANT J2 J1 J3 J4 J5 J7 J6 J2 WR2_ANT WR1_ANT WR1_ANT J2 WR2_ANT J2 43
Page 1 and 2: Installation Manual SSB RADIOTELEPH
Page 3 and 4: SAFETY INSTRUCTIONS The installer m
Page 5 and 6: SYSTEM CONFIGURATION * 3 For DSC ro
Page 7 and 8: EQUIPMENT LIST Name Type Code No. R
Page 9 and 10: 1. HOW TO INSTALL THE SYSTEM 1.1 Co
Page 11 and 12: 1. HOW TO INSTALL THE SYSTEM 1.2 An
Page 13 and 14: 1. HOW TO INSTALL THE SYSTEM 1.2.3
Page 15 and 16: 1. HOW TO INSTALL THE SYSTEM 1.5 An
Page 19 and 20: 1. HOW TO INSTALL THE SYSTEM 3. Fas
Page 23 and 24: Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Page 25 and 26: Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10
Page 27 and 28: 2. WIRING 4. Connect the signal cab
Page 29 and 30: 2. WIRING 2.1.2 Connections for out
Page 31 and 32: 2. WIRING Locking wire saddle Cable
Page 33 and 34: 2. WIRING 2.3 Control Unit Connect
Page 35 and 36: 2. WIRING MIF unit Use connector 17
Page 37 and 38: 2. WIRING 110 110 100 100 100V 10%
Page 39 and 40: 2. WIRING 2.6 Automatic Antenna Swi
Page 41 and 42: 3. INITIAL SETTINGS 2. Enter the pa
Page 43 and 44: 3. INITIAL SETTINGS 3.4.3 DSC SETUP
Page 45 and 46: 3. INITIAL SETTINGS DIVIDER: Divide
Page 47 and 48: 3. INITIAL SETTINGS TX PWR (TUNE) x
Page 49: 3. INITIAL SETTINGS Standard config
Page 53 and 54: APPENDIX 1 JIS CABLE GUIDE Cables l
Page 55 and 56: A-3
Page 57 and 58: A-7
Page 59 and 60: A-11
Page 61 and 62: A-15
Page 63: D-2
Page 66 and 67: D-4
Page 70 and 71: D-6
Page 72 and 73: D-8
Page 74 and 75: D-10
Page 86 and 87: 2 3 4 5 6 A B C D *2 MJ-A3SPF0023 -

FS1575_2575_5075 Installation Manual E1 6-15-2012 - Furuno USA

Create successful ePaper yourself

Delete template?

Save as template?