LINX 7-5 Turn-Key Application User's Guide - LINX Data Terminals

More documents

Recommendations

Info

Terminal: Post Validation Prompt Options Screen Note: this field MUST be used! The Post Validation Prompt Screen will initialize the format of the response message displayed after a validation attempt. The same format codes can be used as in previous prompt screens. However, these are the ONLY prompts where format code: “%V” is valid. Since %V inserts the “Validation Response Data”, the validation data is not “defined”: until this point in the application. The display time of these prompts can be set and the validation response can optionally be sent to a COM port (logging?) Entry Fields: Post Entry Prompt Line #1 Format: This field is used to provide the format (or text) to display on line #1 after validating the entry data. This can be a generic message such as “Badge Accepted” or in the case of a Menu application, the message can be more specific ( as above). Note: this field is optional! Post Entry Prompt Line #2 Format: This field is used to provide the format (or text) to display on Line #2 after validating the entry data. This message is usually quite generic such as “Thank You”. However, if validation is performed, the message can be the result of the validation extraction. For instance, if the extraction was defined to extract the “Name” field, then this could display: “Thank You – John Smith” (as above). Prompt Display Duration: This field defines the number of seconds that the Post Validation Prompts are shown. Send Validation Data to COM Port: This option provides means to send the validation response data to a device on the COM port. This may be serial printer or a terminal program (ProComm). This provides a way to print receipts for a transaction. All is required to return the receipt data as the Validation response. This should normally be performed by a Host validation mode! 36 • Turn-Key Configurator Entry Screens-In Detail LINX 7-5 Turn-Key Application User's Guide
Terminal: End of Configuration Screen PC Host: Start Screen This screen offers the option to continue to create a Host Application configuration. At this point the LINX7-5 terminal configuration “Lx75_TK.cfg”has been generated and saved to the default directory. This directory is the directory that contains the Configuration wizard executable, filename: “TK_CONFIG.exe”. The Lx75_TK.cfg file must be downloaded to the terminal as indicated and the terminal rebooted to instantiate the new Turn-key configuration. LINX 7-5 Turn-Key Application User's Guide Turn-Key Configurator Entry Screens-In Detail • 37
Page 1 and 2: LINX 7-5 Turn-Key Application User'
Page 3 and 4: Contents Overview: 1 What is the Tu
Page 5 and 6: Overview: What is the Turn-Key Appl
Page 7 and 8: • Each Submenu defined can also h
Page 9 and 10: • Validation response can be sele
Page 11 and 12: Note This should never be changed u
Page 13 and 14: Main Status Monitor Window: Once co
Page 15 and 16: Saving Unsolicited Data Each time y
Page 17 and 18: File Transfer Utility The LINX File
Page 19 and 20: Turn-Key Configurator Entry Screens
Page 21 and 22: Terminal: Program Constraint Option
Page 23 and 24: Entry Fields: Afternoon Break Start
Page 25 and 26: The alignment of the display prompt
Page 27 and 28: The Application Input Configuration
Page 29 and 30: Terminal: MSR Input Qualification S
Page 31 and 32: Note: Whatever name has been define
Page 33 and 34: Prompt for Finger Scan: This option
Page 35 and 36: Fixed Length Field Mode: Start Posi
Page 37 and 38: Terminal: Record Validation Control
Page 39: Note: Any day that does not have va
Page 43 and 44: However, if not, then a periodic Ho
Page 45 and 46: The Host Validation Record Extract
Page 47 and 48: Sample Applications Sample #1: A sm
Page 49 and 50: Door Access enabled. Local Storage
Page 51 and 52: Default used for Bar Code input qua
Page 53 and 54: Note: Extracted Field #2 is employe
Page 55 and 56: Summary of the current configuratio
Page 57 and 58: COMInDataLen=1 UseBells=0 UseDoor=1
Page 59 and 60: +MinFKey=1 +MaxFKey=10 +FKeyInRecor
Page 61 and 62: +FKeyControls[11].Line2=Prompt Line
Page 63 and 64: SyncTime=03:00 HostValidationMode=0
Page 65 and 66: For each task, an employee must fir
Page 67 and 68: Main prompts - Line #1 will display
Page 69 and 70: Note: “Format as part of record
Page 71 and 72: F4 (STOP TASK) prompts.. IN (Clock
Page 73 and 74: No Filtering - defaults used.. Use
Page 75 and 76: Above: Summary of Current configura
Page 77 and 78: Press F4 to actually start the JOB.
Page 79 and 80: Define Desired BELLs.. Set Door (In
Page 81 and 82: First submenu (START JOB submenu1)
Page 83 and 84: Bar Code defaults used.. Define thi
Page 85 and 86: Submenu 1-1 (EMP-ID) Extract field
Page 87 and 88: Submenu 1-2 (JOB#): Allow Bar Code,
Page 89 and 90: Submenu 1-2(Job #) No badge filteri
Page 91 and 92:
Submenu 1-3(Proc#) Allow Bar Codes,
Page 93 and 94:
Submenu 1-3(Proc#): Qualifications
Page 95 and 96:
Submenu 1-4(Start JOB): Define prom
Page 97 and 98:
Submenu 1-4(Start-JOB): Inputs qual
Page 99 and 100:
Submenu 1-4(Start JOB): No Time/Day
Page 101 and 102:
Submenu 2-1(ID): Define prompts for
Page 103 and 104:
Submenu 2-1(ID): All inputs qualifi
Page 105 and 106:
Submenu 2-1(ID): No Time/day valida
Page 107 and 108:
Submenu 2-2(Job Number): Default Ba
Page 109 and 110:
Submenu 2-2 (Job Number): Define re
Page 111 and 112:
Submenu 2-3(End Job): Use bar code
Page 113 and 114:
Submenu 2-3(End Job): Define record
Page 115 and 116:
The LINX7-5 control file:”Lx75_TK
Page 117 and 118:
Host application control file: ”P
Page 119:
LINX 7-5 Turn-Key Application User'
show all

LINX 7-5 Turn-Key Application User's Guide - LINX Data Terminals

Create successful ePaper yourself

Delete template?

Save as template?