LINX 7-5 Turn-Key Application User's Guide - LINX Data Terminals

More documents

Recommendations

Info

• A subset of the validation record can also be extracted to be used as a validation response. This allows non-ID data to be used for displaying results. The extraction can be performed via "Separator Character" mode or Fixed length field mode. An Example validation record: Field: ID Name Address Vac, Sick Contact Tel No. 1005675,Mary Smith, Concord MA, 25, 16, Paul Smith, 6314562001 • The ID is "validated" against the first field, the second field "Name" is returned by extraction to the application. If the remaining vacation hours is desired, then field #4 would be extracted. In this example the "obvious" extraction mode is "Separator Character" mode, since the record is "Comma" delimited (most common type) • If "ONLINE" mode is used, the application can be configured to "not" attempt validation, (if validation has been requested), when the Host goes "Offline". The record would be just saved in the queue until the Host re-connects. • Validation can also be extended to include valid time and day access. A validation record is created that contains fields for "Valid Start" and "Valid End" times for every day of the week. If an entry is attempted out of the defined range then validation will FAIL and access will be denied! • Post validation prompts can be defined. Alignment and duration is selectable. • The validation response can be optionally be sent to a COM Port. • And last but not least, a previously created .CFG file can be imported to allow easy further customization of a current application. Turn-Key PC Host Software Functions: Note: This periodic interval is also the FTP connect interval if FTP transfer mode is selected. • If operating in BATCH mode, the Host program can either use 1.) FTP (if a local file is stored on the terminal), or 2.) periodically connect to the terminal to retrieve data stored in the Host queue. The periodic connect interval is configurable and the default is 15 minutes. When online mode or periodically connect to the terminal is selected, all data retrieved from the terminals’ Host queue, is saved in the file in the working directory named “zdata.txt”. • Terminal Time-synchronization can be optionally performed once a day. This will eliminate any slight time drifts. • Up to 3 files can be scheduled for downloading, once a day, at a user configurable time. • Up to 3 files can be scheduled for uploading, once a day, at a user configurable time. • Validation can be performed using a local Host file. The name of this file is configurable. • Validation ID data can be extracted using either "Separator Character" mode or Fixed Field” Mode. 4 • Turn-Key Application Features LINX 7-5 Turn-Key Application User's Guide
• Validation response can be selected as "Generic" or Selected". "Generic" indicates that a "Generic" response message will be returned. However "Selected" indicates that special data will be returned on successful validation. • "Generic" Good validation response message can be customized. • "Failed" validation response can be customized. This response will be returned on any failed validation attempt. • "Selected" validation response can be either a complete record or a subset. The subset can be selected via an "Extract data" option. • Extracted response data can use either "Separator Character" mode or “Fixed Field” Mode. Host Control Application Screenshot: Terminal IP Range Setup Form: LINX 7-5 Turn-Key Application User's Guide Turn-Key Application Features • 5
Page 1 and 2: LINX 7-5 Turn-Key Application User'
Page 3 and 4: Contents Overview: 1 What is the Tu
Page 5 and 6: Overview: What is the Turn-Key Appl
Page 7: • Each Submenu defined can also h
Page 11 and 12: Note This should never be changed u
Page 13 and 14: Main Status Monitor Window: Once co
Page 15 and 16: Saving Unsolicited Data Each time y
Page 17 and 18: File Transfer Utility The LINX File
Page 19 and 20: Turn-Key Configurator Entry Screens
Page 21 and 22: Terminal: Program Constraint Option
Page 23 and 24: Entry Fields: Afternoon Break Start
Page 25 and 26: The alignment of the display prompt
Page 27 and 28: The Application Input Configuration
Page 29 and 30: Terminal: MSR Input Qualification S
Page 31 and 32: Note: Whatever name has been define
Page 33 and 34: Prompt for Finger Scan: This option
Page 35 and 36: Fixed Length Field Mode: Start Posi
Page 37 and 38: Terminal: Record Validation Control
Page 39 and 40: Note: Any day that does not have va
Page 41 and 42: Terminal: End of Configuration Scre
Page 43 and 44: However, if not, then a periodic Ho
Page 45 and 46: The Host Validation Record Extract
Page 47 and 48: Sample Applications Sample #1: A sm
Page 49 and 50: Door Access enabled. Local Storage
Page 51 and 52: Default used for Bar Code input qua
Page 53 and 54: Note: Extracted Field #2 is employe
Page 55 and 56: Summary of the current configuratio
Page 57 and 58: COMInDataLen=1 UseBells=0 UseDoor=1
Page 59 and 60:
+MinFKey=1 +MaxFKey=10 +FKeyInRecor
Page 61 and 62:
+FKeyControls[11].Line2=Prompt Line
Page 63 and 64:
SyncTime=03:00 HostValidationMode=0
Page 65 and 66:
For each task, an employee must fir
Page 67 and 68:
Main prompts - Line #1 will display
Page 69 and 70:
Note: “Format as part of record
Page 71 and 72:
F4 (STOP TASK) prompts.. IN (Clock
Page 73 and 74:
No Filtering - defaults used.. Use
Page 75 and 76:
Above: Summary of Current configura
Page 77 and 78:
Press F4 to actually start the JOB.
Page 79 and 80:
Define Desired BELLs.. Set Door (In
Page 81 and 82:
First submenu (START JOB submenu1)
Page 83 and 84:
Bar Code defaults used.. Define thi
Page 85 and 86:
Submenu 1-1 (EMP-ID) Extract field
Page 87 and 88:
Submenu 1-2 (JOB#): Allow Bar Code,
Page 89 and 90:
Submenu 1-2(Job #) No badge filteri
Page 91 and 92:
Submenu 1-3(Proc#) Allow Bar Codes,
Page 93 and 94:
Submenu 1-3(Proc#): Qualifications
Page 95 and 96:
Submenu 1-4(Start JOB): Define prom
Page 97 and 98:
Submenu 1-4(Start-JOB): Inputs qual
Page 99 and 100:
Submenu 1-4(Start JOB): No Time/Day
Page 101 and 102:
Submenu 2-1(ID): Define prompts for
Page 103 and 104:
Submenu 2-1(ID): All inputs qualifi
Page 105 and 106:
Submenu 2-1(ID): No Time/day valida
Page 107 and 108:
Submenu 2-2(Job Number): Default Ba
Page 109 and 110:
Submenu 2-2 (Job Number): Define re
Page 111 and 112:
Submenu 2-3(End Job): Use bar code
Page 113 and 114:
Submenu 2-3(End Job): Define record
Page 115 and 116:
The LINX7-5 control file:”Lx75_TK
Page 117 and 118:
Host application control file: ”P
Page 119:
LINX 7-5 Turn-Key Application User'
show all

LINX 7-5 Turn-Key Application User's Guide - LINX Data Terminals

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?