LINX 7-5 Turn-Key Application User's Guide - LINX Data Terminals

More documents

Recommendations

Info

Entry Fields: Validation Record Source: These radio buttons define the source of the validation data. Note: The database option is currently not available! Enter Local Validation Record File Name: The field is used to define the name of Local Host validation file. This file will be used to verify data from the terminal. On validation success, a generic response, or a record from this file (or part of the record) will be returned to the terminal as a validation response. Select Database Type: These radio buttons will specify the type of database that will be supporting validation requests. Note: Database support is not currently available. Validation Response Selection: These radio buttons specify whether to return a generic response to a validation request or a “selected” response. Note: “Selected” should be chosen if specific data from the validation record is returned. This applies whether the entire record or part of the validation record is returned! Generic “GOOD” Validation Response: This field should be initialized with a default “GOOD” response when a validation was successful. This is only used if “Generic” was selected above! Failed Validation Response: This field should be initialized with a failure response message for unsuccessful validations. Note: This message will be returned for “Generic” and “Selected” modes! Extract Data From Validation Record: This checkbox should be enabled if “only a portion” of the validation record should be returned after a successful validation. This data will be extracted using the method determined on the Validation Record Extract Options screen which follows. PC Host: Validation Data Extract Options Screen 40 • Turn-Key Configurator Entry Screens-In Detail LINX 7-5 Turn-Key Application User's Guide
The Host Validation Record Extract Options screen specifies the method to locate the validate field within the validation file (or database) and the extract mode if a portion of the data should be returned as a response. Entry Fields: Select Validation Field Extract Method: These two radio buttons specify the locating method for the Validation ID field. This field is the one used to match the entry data for validation. The extract method is either Fixed Length Field or Separator Character Mode. – Default is “Separator Character” mode. Fixed Length Field Mode: Start Position:. This field is used to indicate the start column of the first character in the Fixed Length field to extract. The range is 1-110, - No default. Fixed Length Field Mode: Field Length: This field is used to specify the length of the fixed length field. Range is 1-110. Separator Character Mode: Field Separator Character:.. This field specifies the special separator character used to extract the data. Default is’,’ (comma). Separator Character Mode: Field Number:. This field indicates the field number of the data to extract. Range 1-110. Default is ‘1’. Extract Validation Data (from Data source) . These fields will be enabled if “Extract Data From Validation Record” was checked on the previous screen. Fixed Length Field Mode: Start Position:. This field is used to indicate the start column of the first character in the Fixed Length field to extract. The range is 1-110, - No default. Fixed Length Field Mode: Field Length: This field is used to specify the length of the fixed length field. Range is 1-110. Separator Character Mode: Field Separator Character:.. This field specifies the special separator character used to extract the data. Default is’,’ (comma). Separator Character Mode: Field Number:. This field indicates the field number of the data to extract. Range 1-110. Default is ‘1’. LINX 7-5 Turn-Key Application User's Guide Turn-Key Configurator Entry Screens-In Detail • 41
Page 1 and 2: LINX 7-5 Turn-Key Application User'
Page 3 and 4: Contents Overview: 1 What is the Tu
Page 5 and 6: Overview: What is the Turn-Key Appl
Page 7 and 8: • Each Submenu defined can also h
Page 9 and 10: • Validation response can be sele
Page 11 and 12: Note This should never be changed u
Page 13 and 14: Main Status Monitor Window: Once co
Page 15 and 16: Saving Unsolicited Data Each time y
Page 17 and 18: File Transfer Utility The LINX File
Page 19 and 20: Turn-Key Configurator Entry Screens
Page 21 and 22: Terminal: Program Constraint Option
Page 23 and 24: Entry Fields: Afternoon Break Start
Page 25 and 26: The alignment of the display prompt
Page 27 and 28: The Application Input Configuration
Page 29 and 30: Terminal: MSR Input Qualification S
Page 31 and 32: Note: Whatever name has been define
Page 33 and 34: Prompt for Finger Scan: This option
Page 35 and 36: Fixed Length Field Mode: Start Posi
Page 37 and 38: Terminal: Record Validation Control
Page 39 and 40: Note: Any day that does not have va
Page 41 and 42: Terminal: End of Configuration Scre
Page 43: However, if not, then a periodic Ho
Page 47 and 48: Sample Applications Sample #1: A sm
Page 49 and 50: Door Access enabled. Local Storage
Page 51 and 52: Default used for Bar Code input qua
Page 53 and 54: Note: Extracted Field #2 is employe
Page 55 and 56: Summary of the current configuratio
Page 57 and 58: COMInDataLen=1 UseBells=0 UseDoor=1
Page 59 and 60: +MinFKey=1 +MaxFKey=10 +FKeyInRecor
Page 61 and 62: +FKeyControls[11].Line2=Prompt Line
Page 63 and 64: SyncTime=03:00 HostValidationMode=0
Page 65 and 66: For each task, an employee must fir
Page 67 and 68: Main prompts - Line #1 will display
Page 69 and 70: Note: “Format as part of record
Page 71 and 72: F4 (STOP TASK) prompts.. IN (Clock
Page 73 and 74: No Filtering - defaults used.. Use
Page 75 and 76: Above: Summary of Current configura
Page 77 and 78: Press F4 to actually start the JOB.
Page 79 and 80: Define Desired BELLs.. Set Door (In
Page 81 and 82: First submenu (START JOB submenu1)
Page 83 and 84: Bar Code defaults used.. Define thi
Page 85 and 86: Submenu 1-1 (EMP-ID) Extract field
Page 87 and 88: Submenu 1-2 (JOB#): Allow Bar Code,
Page 89 and 90: Submenu 1-2(Job #) No badge filteri
Page 91 and 92: Submenu 1-3(Proc#) Allow Bar Codes,
Page 93 and 94: Submenu 1-3(Proc#): Qualifications
Page 95 and 96:
Submenu 1-4(Start JOB): Define prom
Page 97 and 98:
Submenu 1-4(Start-JOB): Inputs qual
Page 99 and 100:
Submenu 1-4(Start JOB): No Time/Day
Page 101 and 102:
Submenu 2-1(ID): Define prompts for
Page 103 and 104:
Submenu 2-1(ID): All inputs qualifi
Page 105 and 106:
Submenu 2-1(ID): No Time/day valida
Page 107 and 108:
Submenu 2-2(Job Number): Default Ba
Page 109 and 110:
Submenu 2-2 (Job Number): Define re
Page 111 and 112:
Submenu 2-3(End Job): Use bar code
Page 113 and 114:
Submenu 2-3(End Job): Define record
Page 115 and 116:
The LINX7-5 control file:”Lx75_TK
Page 117 and 118:
Host application control file: ”P
Page 119:
LINX 7-5 Turn-Key Application User'
show all

LINX 7-5 Turn-Key Application User's Guide - LINX Data Terminals

Create successful ePaper yourself

Delete template?

Save as template?