LTC2410 24-Bit No Latency âÎ£TM ADC with Differential Input and ...

More documents

Recommendations

Info

LTC2410APPLICATIO S I FORATIOU W U U15VQ12N390422Ω20Ω1C10.1µF+1/2LT1112–32+5VC347µFLT1236-5C10.1µF350Ω BRIDGETWO ELEMENTSVARYING10V1RN110k234RN110k34V CCLTC2410REF +REF –25V–5V5RN110k687RN110k56IN +IN –GND1, 7, 8, 9,10, 15, 1633Ω×2Q2, Q32N3906×220Ω7C20.1µF15V8–1/2LT11124+65RN1 IS CADDOCK T914 10K-010-02–15V–15V2410 F53Figure 53. Use Resistor Arrays to Provide Precise Matching in Excitation Amplifier5V5V1612 47µF1415+34V CCREF +REF –2TO OTHERDEVICES11152474HC4052133656IN +LTC2410IN – GND1, 7, 8, 9,891010, 15, 16A0A12410 F54Figure 54. Use a Differential Multiplexer to Expand Channel Capability42
LTC2410TYPICAL APPLICATIO SUSample Driver for LTC2410 SPI InterfaceThe LTC2410 has a very simple serial interface that makesinterfacing to microprocessors and microcontrollers veryeasy.The listing in Figure 56 is a simple assembler routine forthe 68HC11 microcontroller. It uses PORT D, configuringit for SPI data transfer between the controller and theLTC2410. Figure 55 shows the simple 3-wire SPIconnection.The code begins by declaring variables and allocating fourmemory locations to store the 32-bit conversion result.This is followed by initializing PORT D’s SPI configuration.The program then enters the main sequence. It activatesthe LTC2410’s serial interface by setting the SS outputlow, sending a logic low to CS. It next waits in a loop fora logic low on the data line, signifying end-of-conversion.After the loop is satisfied, four SPI transfers are completed,retrieving the conversion. The main sequence endsby setting SS high. This places the LTC2410’s serialinterface in a high impedance state and initiates anotherconversion.The performance of the LTC2410 can be verified using thedemonstration board DC291A, see Figure 57 for theschematic. This circuit uses the computer’s serial port togenerate power and the SPI digital signals necessary forstarting a conversion and reading the result. It includes aLabview application software program (see Figure 58)which graphically captures the conversion results. It canbe used to determine noise performance, stability andwith an external source, linearity. As exemplified in theschematic, the LTC2410 is extremely easy to use. Thisdemonstration board and associated software is availableby contacting Linear Technology.LTC2410SCKSDOCS13121168HC11SCK (PD4)MISO (PD2)SS (PD5)2410 F55Figure 55. Connecting the LTC2410 to a 68HC11 MCU Using the SPI Serial Interface43
Page 1 and 2: FEATURES■■■■■■■■■
Page 3 and 4: CO VERTER CHARACTERISTICSUThe ● d
Page 5: TII G CHARACTERISTICSU WLTC2410The
Page 9 and 10: LTC2410TYPICAL PERFOR A CE CHARACTE
Page 11 and 12: LTC2410WFU CTIO AL BLOCK DIAGRAV CC
Page 13 and 14: LTC2410APPLICATIO S I FORATIOU W U
Page 17: LTC2410APPLICATIO S I FORATIOU W U
Page 26 and 27: LTC2410APPLICATIO S I FOR26ATIOU W
Page 44 and 45: LTC2410TYPICAL APPLICATIO SU*******
Page 46 and 47: LTC2410TYPICAL APPLICATIO SV CCBANA
Page 48: LTC2410U WPCB LAYOUT A D FILBottom

LTC2410 24-Bit No Latency âÎ£TM ADC with Differential Input and ...

Create successful ePaper yourself

Delete template?

Save as template?

LTC2410 24-Bit No Latency âÎ£TM ADC with Differential Input and ...