Catalog 08-2001 without prices - nl3prc

Manufacturer's certificate of calibration available!Reference units for calibrating/checking any thermometer system, highest accuracyand resolution (0,1°C from -199.9 to +650.0°C).Use any cable length without recalibrationThe unit thattalks!Low price resistance thermometer forPt100 - plug-in probes,battery and mains operation possible.MICROPROCESSOR PRECISION THERMOMETER Pt100 4-wireGMH 2000 SA GMH 2000Battery or mains operation, serial interface, for plug-in probesApplication: GMH 2000 SA (with voice output) is used as a reference unit or for highly accurate measurementsin liquids, soft media, air/gases or for any application where the visibility is bad (e.g. in darkness, darkrooms, for visually handicapped persons etc.) or where a display cannot be constantly monitored becausesome other process has to be supervised. Due to the integrated min./max. value memory the unit can also beused for comparative measurements at new installations whithout constant supervision being necessary.GMH 2000 (without voice output) otherwise identical to GMH 2000 SA - a low price reference unit.Specification:Measuring range: GMH2000SA: -199,9 ... +650,0 °CGMH2000: -199,9 ... +650,0 °C resp. -199,9 ... +999,9 °Resolution: 0,1 °C (GMH2000SA) resp. 0,1 °C or 0,1 ° (GMH2000)Linearisation: parameters stored digitallyAccuracy: < 0,03 % f.s. ± 1 digitWorking temperature: 0 to 50 °CStorage temperature: -20 to +70 °CProbe: Pt100, 4-wire, (not included - please order separately!) 4-pin miniature DIN-plug.Switch positions: GMH2000SA 0 = Off GMH2000 0 = Off1 = measuring without voice output 1 = °C2 = measuring with voice output 2 = °3 = measuring with voice output andnumber sequence for record purposesDisplay: 3 off 4 digit LCD-displays for simultaneous display of the current value (digits 12.4 mm high) aswell as of min./max. values (digit height 7 mm each). Automatic segment test when device is switched on.Change indicator: for rising or falling temperatures an arrow pointing upwards or downwards isdisplayed at the left side next to the current value.Probe damage display: display value disappears and is replaced by dashes.Min-/max-value memory: activated when device is switched on. Any min. or max. valuemeasured after unit is switched on will be continuously displayed and constantly updated ifnecessary. These values will be deleted as soon as the unit is switched off.Serial interface: socket for external RS232 compatible serial interface.suitable interface module: GRS232 - please order separately.Power supply: 9V-Batterie type IEC 622 (included) or regulated power supply 12V DC (typeGNG09). Power supply connectors for 2,5 mm jack connector.(Automatic battery disconnection when connecting power supply.)Low battery warning: „BAT“ is displayed in the top left-hand corner in case of low voltage.Power consumption: GMH2000 resp. GMH2000SA-switch position 1: < 10 mAGMH2000SA-position 2/3: approx. 15-35 mA (depending on volume set)Dimensions: approx. 150 x 86 x 30 mm (H x W x D). Impact resistant ABS plastic case withintegrated pop-up clip for table top or suspended operation, and lateral holders for probe handle.Weight (device only): approx. 250 g (GMH2000), approx. 275 g (GMH2000SA)Accessories against upcharge - please order separately!:GRS 232 interface adapter for connection of a GMH2000/SA to an . . . . . . . . . . .RS232-interface of a PC. (Software GSOT2000 for recording and displaycan be downloaded free of charge from our Internet Homepage)Plug-in Pt100-probe, 4-wire DIN class B (± 0,3°C at 0°C)GT 601 immersion/air/gas probe, -200 to +600°C . . . . . . . . . . . . . . . . . .GT 401 immersion probe, -50 to +400°C . . . . . . . . . . . . . . . . . . . . . .GES 401 insertion probe for soft media, -50 to +400°C . . . . . . . . . . . . . . . .Sensor with higher accuracy 1/10 DIN (± 0,03°C at 0°C - measuring range: -50 ... +250°C) . . UpchargeGKK 1100 plastic case (340 x 275 x 83 mm) with foam lining . . . . . . . . . . . . .GNG 09 regulated power supply (220/240V, 50/60Hz, 12VDC) . . . . . . . . . . . .DIGITAL HAND-HELDTHERMOMETERGTH 400Pt100 (2-wire)Battery/mains operation for plug-inprobesApplications: accurate measurements in liquids,soft media, air/gases.Specification:Measuring range: -50 ... +400 °CResolution: 1°CAccuracy: unit: 0,2% ±1digitprobe: Pt100 acc. to DIN class B standardsProbe: Pt100, 2-wire connection via 3.5 mmjack connector.or suitable probes, mounted volt-free, pleasesee below or on page 12.Probes not included - please order separately!Display: 3½ digit LCD, approx. 13mm highWorking temperature: 0 to 45 °CStorage temperature: -20 to +70 °CPower supply: 9V battery type IEC 622(included). Additional dc power connector for2.5 mm jack connector. (Battery disconnectedautomatically)Battery service life: approx. 50 to 100 hours,for permanent use we recommend our powersupply GNG10.Low battery warning: „BAT“Dimensions: approx. 150 x 86 x 30 mm (H x W x D).impact resistant ABS plastic case with integratedpop-up clip for table top or suspended operation,and lateral holders for probe handle.Weight: approx. 230 g (incl. battery)Accessories:Suitable plug-in temperature probes:(Probes interchangeable without recalibration!)GT 150 immersion probefor liquids, aggressive or dusty gasesGES 150 insertion probefor soft materialGKK 1100 case(340 x 275 x 83 mm) with foam liningGKK 3500 case(394 x 294 x 106 mm) with punched foam lining fordevice and 3 probes with handle, spare batt. etc.GNG 10 power supplyPlease note: for surface measurements werecommend our quick rsponse thermometersNiCr-Ni (type K)9