2 - Big Ass Fans

More documents

Recommendations

Info

248’–24’ POWERFOIL ® X2.0 & 10’–24’ POWERFOIL ® X2.0PLUS FANSInstalling Guy Wires (cont.)3. Route guy wire through Gripple ®Route the guy wire through the Gripple, the carabiner on the main fan unit, and then back through the Gripple as shown. Do not tightenthe Gripple until the remaining guy wires have been installed.4. Install remaining guy wiresCAUTION: Over-tightening the guy wires could throw the fan off balance.ATTENTION : Un serrage excessif des câbles de retenue risque de déséquilibrer leventilateur.Wire Rope ClipRepeat steps 2–3 to install the three remaining guy wires.Evenly cinch all four guy wires into place using the Gripples. The guy wires should be taut,evenly spaced around the fan, and away from the path of the airfoils. Maintain a distance of 6”–8”between the Gripple and the carabiner.Once all of the guy wires are taut, secure their loose ends with the wire rope clips and torque to4.5 ft·lb (6.1 N·m). WWW.BIGASSFANS.COM ©2012 DELTA T CORP. DBA BIG ASS FAN CO. ALL RIGHTS RESERVED
8’–24’ POWERFOIL ® X2.0 & 10’–24’ POWERFOIL ® X2.0PLUS FANSInstalling Airfoils25Big Ass Fans recommends completing Electrical Installation (p. 28) before installing the airfoils.WARNING: Disconnect power to the fan before installing the airfoils.AVERTISSEMENT : Débranchez l’alimentation du ventilateur avant de replacer les hélices.1. Attach winglets to airfoilsNote: Check each airfoil to ensure the AirFence is still securely attached.Attach the winglet to the airfoil using the Winglet Hardware as shown. Boththe fasteners. to the fan.Winglet Hardware (BAF-Supplied):a. (10) 10-24 x 1/2” Boltb. (10) 10-24 x 3/4” BarrelAirFencePowerfoilPlusPowerfoilaabb2. Position airfoilsSlide the airfoils onto the tabs of the fan hub. The airfoils must beattached to the fan hub with the curved sides facing downward.Do not fasten the airfoils to the hub with hardware at this point.Proceed to step 3.WWW.BIGASSFANS.COM ©2012 DELTA T CORP. DBA BIG ASS FAN CO. ALL RIGHTS RESERVED
Page 3: 8’-24’ POWERFOIL ® X2.0 & 10
Page 6 and 7: 8’-24’ POWERFOIL ® ® X2.0PLU
Page 8 and 9: 8’-24’ POWERFOIL ® X2.0 & 10
Page 13 and 14: Parts and hardware8’-24’ POWERF
Page 15 and 16: Fan diagram8’-24’ POWERFOIL ®
Page 17 and 18: Préparation du lieu de travail8’
Page 31: 8’-24’ POWERFOIL ® X2.0 & 10
Page 39 and 40: Delta secondary8’-24’ POWERFOIL
Page 47 and 48: Wiring: Fan controller with line re
Page 49 and 50: Daisy chaining (cont.)8’-24’ PO
Page 53 and 54: Wiring: Fire signal relay (M series
Page 57 and 58: Understanding and clearing fan faul
Page 59 and 60: Locking and unlocking procedures8
Page 63: Annual Maintenance ChecklistFan Mod
Page 73 and 74: Warranty Claim Form800 Winchester R
Page 75 and 76: Check-In Procedure(for Big Ass 2348
Page 77 and 78: Close-Out Procedure(for Big Ass 234
Page 80: *002788-01*002788-012348 Innovation

2 - Big Ass Fans

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?