DATA INVOLTAGE SELECTWARNING: CHANGE VOLTAGE SELECT ONLY WI TH POWER REMOVED.CAU TION : HOT R EMOVE POW ER BEFORE RELAMPINGUSER MANUAL.DATA OUTTI LTMSP EEDGOB OANALOG IN0-10VANALOGGND7SHUTTERCOLORPANDIM24 VDCADDRESS010203040506070809101112GND4 2 51 386 7FOR FUTHER INFORMATIONCONSULT USERS MANUALnone121,231,32,31,2,341,42,41,2,42209 WEST BRAKER LANE, AUSTIN, TEXAS U.S.A.ADDRESS131415161718192021222324FOR FURTHER INFORMATIONPLEASE CONSULT USER MANUALPERSONALI TYFI XT URE MODE SWI TCHES 1-2SET-UPLAMP SAVE3,41,3,42,3,41,2,3,451,52,51,2,53,51,3,52,3,51,2,3,5CONTROL MODE SWITCHES 3-8SWITCHESON38Understanding LED Indicatorsnd Audio-Visual Phone: courtesy 0870 of Services 080 2342mail: enquiries@sxsevents.co.ukwww.sxsevents.co.ukThis section describes the LEDs (Light Emitting Diode) on the<strong>Trackspot</strong> rear panel: Fan, Enable, and Audio (see Figure 1-4). If youare experiencing problems with your <strong>Trackspot</strong> fixture, these LEDsmay provide insight on where the problem is originating. See “” onpage 4-1 for possible solutions to LED-related symptoms.140200120240WARNING: NOT FOR RESI DENTIAL USE. TO REDUCE THE RISK OFFIRE ORELECTRICSHOCK, DO NOTEXPOSE TO RAINOR MOISTURE,NO USERSERVI CEABLE PA RTS INSIDE. REFER SERVICING TOQUALIFI ED SERVI CE PERSONNEL. FOR SAFE OPERATION CONSULT100220FUSEFAN®trackspotENABLEONSWITCHESLI GHTWAVE RESEARCHADDRESSONSWITCHESPERSONALITYAUDIOMICFan LEDEnable LEDAudio LEDMODELSERIALFACTORY SET VACWATTSHZDATEQC61 4 2 853OUT(UNREG.)INPUTSPECIAL ANALOGNORMAL RUNSELF TESTLIGHTWAVE CONTROLDMX 1-256DMX 257-512ANALOGAUDIO (SLAVE)AUDIO (MASTER)PAN INVERTTI LT INVERTNONE121,2NONE544,5FOR FURTHER INFORMATIONPLEASE CONSULT USER MANUAL67Figure 1-4. LED location on the rear panelFan LEDThe red Fan LED monitors the voltage to the cooling fan. The Fan LEDilluminates when the fixture is first powered up, and stays illuminatedfor two minutes after the lamp is extinguished. <strong>Trackspot</strong> comesequipped with thermal overload protection to automatically extinguishthe lamp if the maximum temperature inside the fixture is exceeded. Ifthe fixture overheats, the Fan LED will flash four times, pause, andrepeat.Enable LEDThe yellow Enable LED monitors the power applied to the motors. TheEnable LED should be illuminated whenever the fixture is ON. If thelogic board is not receiving the 24 volts required to operate the fixture,the Enable LED will not illuminate.Audio LEDThe green Audio LED monitors the fixture’s response to sound. TheAudio LED illuminates when the fixture is ON and ambient bass isregistered, regardless of the configuration. (If the fixture is notprogrammed to receive audio bass frequencies, the sound trigger isignored.)www.sxsevents.co.uk1-4 Understanding LED Indicators <strong>Trackspot</strong> User <strong>Manual</strong>
Chapter 2Configuring courtesy Your of <strong>Trackspot</strong> ®nd Audio-Visual Phone: 0870 Services 080 2342mail: enquiries@sxsevents.co.ukwww.sxsevents.co.ukTo prepare your <strong>Trackspot</strong> for operation, you must choose a controlmode, set the personality and address switches, mount the fixture, linkthe fixture, and focus the fixture.Choosing a Control ModeThere are four different control modes that will operate your <strong>Trackspot</strong>fixture: DMX 512 protocol, LWR protocol, standard analog, and standalone operation (master/slave).When configured for DMX 512 protocol, LWR protocol, or stand aloneoperation, <strong>Trackspot</strong> uses seven contiguous digital channels to controlits constructs. When used with a standard analog controller, <strong>Trackspot</strong>uses either six or seven contiguous analog channels per fixture. Todetermine whether you will use six or seven analog channels, see“Standard Analog” on page 2-15. The digital/analog channels have thefunctions shown in Table 2-1 below:Table 2-1. Channel assignmentsChannelFeature1 Pan2 Tilt3 Color4 Gobo5 Shutter6 Dim7 MSpeed2DMX 512 ProtocolDMX 512 (D for digital, MX for multiplex and 512 is the number ofchannels per link) is a reliable and efficient control protocol.Developed by the United States Institute of Theatre Technology(USITT), DMX 512 is the standard method used in the lighting industryfor controlling lighting fixtures and other devices (such as hazers andlasers).A controller using DMX 512 protocol (such as the Status Cue ® <strong>Lighting</strong>Console) can control a large number of different types of devices madeby various equipment manufacturers, such as High End Systems, onthe same link.www.sxsevents.co.ukYou can control up to 72 <strong>Trackspot</strong>s per DMX 512 link in either low orhigh resolution mode. For more information on resolution modes, see“Start Channels and Construct Parameters” on page A-1.<strong>Trackspot</strong> User <strong>Manual</strong> Choosing a Control Mode 2-1