EO18-12003 - toshiba tec europe

More documents

Recommendations

Info

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-120034.1 PS-2 CONNECTOR (KEYBOARD, MOUSE) AND USB CONNECTOR4. INSTALLATION PROCEDURE FOR OPTIONALEQUIPMENTWARNING!Be sure to unplug the power cord before installing any optional equipment.4.1 PS-2 CONNECTOR (KEYBOARD, MOUSE) AND USB CONNECTOR1) Open the front cover.2) Connect the USB to the left, keyboard to the middle, and mouse to the right connectors, respectively (Referto Fig.4-1).USB ConnectorsPS-2 MousePS-2 KeyboardPower SwitchFig. 4-1NOTES:1. If the DIP switch on the TOUCH MAIN PC board is set, the mouse is available. (For details, referto Section 4.8)2. The USB interface is available only when supported by the operating system which is installedinto the ST-60 POS terminal. This machine does not support the USB-type keyboard and mouse.4.2 DRAWERThe 24V-drive drawers are connectable to the two drawer connectors on the bottom of the terminal. (Refer to Fig.4-2).DRW2TDRW1TFig. 4-2NOTE:When connecting the drawer cable to the ST-60 terminal, attach the enclosed ferrite core to the drawercable.4-1
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-12003(Revision Date: Jun. 21, 2002)4.3 FDD UNIT (FDDST-60-1-QM)4.3 FDD UNIT (FDDST-60-1-QM)1) Open the FDD connector cover.2) Connect the FDD cable to the following FDD connector (Refer to Fig. 4-3).FDD CableFDD ConnectorFig. 4-34.4 HDD (Hard Disk Drive)Master HDD (A, B, C models)1) Remove the top cover. (Refer to Section 3.2.1)2) Remove the four DSM-3x6 screws to detach the 2.5" HDD holder (Refer to Fig. 4-4).DSM-3x6 Screw2.5” HDD HolderDSM-3x6 ScrewFig. 4-43) Install the HDD unit in the 2.5" HDD holder with the four DSM-3x6 screws (accessory). After that, connectthe HDD cable (accessory) to the HDD.NOTE: Make sure of the direction of the HDD cable when connected to the HDD. (Refer to Fig. 4-5).Slave HDDTo Touch Main PC BoardMaster HDDFig. 4-54-2
Page 1 and 2: TEC POS TerminalST-60 SERIESMainten
Page 3 and 4: TABLE OF CONTENTSEO18-12003(Revisio
Page 5 and 6: 1. UNPACKING EO18-12003(Revision Da
Page 7 and 8: 2. BEFORE INSTALLATION EO18-120032.
Page 9 and 10: 3. MAIN UNIT REPLACEMENT EO18-12003
Page 25: 3. MAIN UNIT REPLACEMENT EO18-12003
Page 29 and 30: 4. INSTALLATION PROCEDURE FOR OPTIO
Page 43 and 44: 5. ST-60 BIOS SETUP (A, B models) E
Page 57 and 58: 6. ST-60 BIOS SETUP (C model)EO18-1
Page 71 and 72: 7. DIAGNOSTIC TEST OPERATION (A, B
Page 77 and 78:
7. DIAGNOSTIC TEST OPERATION (A, B
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
8. DIAGNOSTIC TEST OPERATION (C mod
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107:
10. PERIODICAL MAINTENANCE EO18-120
show all

EO18-12003 - toshiba tec europe

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?