METAL FINISHING DEPARTMENT PRODUCTS GUIDE 08CHEMICALS FOR PLATING ON PLASTICSCHEMICALS FOR TOP METALATE PROCESSApplication Trade Name Composition FeatureSURF 2000Concentration as supplied*Pre-etching agent for Poly Ether Imide (Ultem 2000 Series).SURF PPE-1129 CONC250 ml/l*Pre-etching agent for Noryl Resin.Pre-Treatment Agent forLM ETCHANT200 ml/l, HCl : 200 ml/l*Etchant for PPE/PA polymer alloy. *Excellent appearance and adhesion after plating.Plating on Engineering PlasticsSURF PC-724Concentration as supplied*Pre-treatment agent for plating on Poly Carbonate. *Give same degrees of adhesion and appearance with ABS Resin.SURF MULTIConcentration as supplied*Pre-etching agent for plating on Multion Resin. *Give same degrees of adhesion and appearance with ABS Resin.*Plating line for ABS Resin can be applied without modification. *Excellent heat-resistance and impact resistance.CHEMICALS FOR CRP PROCESSApplication Trade Name Composition FeatureCleanerCRP CLEANER50 g/l*Silicate-free alkaline cleaner. *Remove oils, finger prints and dirts on resin surface.CatalyzerCRP CATALYST65 ml/l, HCl : 300 ml/l*Excellent bath stability and good in resistance to chromic acid.Conductivity InducerCRP SELECTORA : 200 ml/l, B : 200 ml/l*Can be applied for long period continuously by replenishment. *Easy waste water treatment, as not containing of formalin and strong chelating agents.CHEMICALS FOR PLATING ON NYLON RESINApplication Trade Name Composition FeatureEtchantTN ETCHANTTR ETCHANT200 ml/l, HCl : 200 ml/l200 ml/l, HCl : 200 ml/l*Give good adhesion by applying with hydrochloric acid. (for Toyobo Nylon Resin)*Give good adhesion by applying with hydrochloric acid. (for Toray Nylon Resin)CatalyzerTN CATALYST170 ~ 200 g/l, HCl : 50 ml/lCatalyst C : 15 ml/l*Additive to prevent aging of nylon resin surface and maintain stability of catalyst.AcceleratorTR POST-ACCELERATOR10 g/l, NaOH : 10 g/l*Enhance sensitivity of catalyst particles inactivated, and improve deposition effects of electroless plating. (For Toray Nylon Resin)TOM PROCESS TREATMENT CHEMICALS (FOR TORAY PBT RESIN)Application Trade Name Composition FeatureEtchant PBT ETCHANT TR200 ml/l, NaOH : 200 g/l *Give roughness to PBT Resin surface, prevent aging of matrix, and give high adhesion.
METAL FINISHING DEPARTMENT PRODUCTS GUIDE 09ZINC PLATING BRIGHTENER AND MIST PREVENTING AGENTBRIGHTENER FOR ALKALINE CYANIDE-FREE BATHApplication Trade Name Composition FeatureNC ZINC 6060B : 2.5 ml/l, 60R : 0.3 ml/lPUR : 2 ml/l*Deposition film has good physical properties, no formation of blister at heat-treatment, and excellent adhesion, brightness and leveling.For Barrel PlatingNC ZINC K-6600MU : 4 ml/l, R : 1 ml/l*Good in brightness at low current density area, and good in chromating effects after baking.NC ZINC K-180K-180 MU : 6 ml/l, CM : 4 ml/lHL : 0.1 ml/l*Nice in plating appearance and good in chromating finish. *As chelating agent free, removal of heavy metals at waste water treatment is easy.*Applicable at high current, and excellent post-processing effects.NC ZINC S-30A : 2 ml/l, B : 8 ml/l*Good productivity, as applicable at full strangth cyanide bath and high current.NC ZINC S-40A : 0.5 ml/l, B : 5 ml/l*At even full strength cyanide bath, can gain excellent brightness and covering power and good physical properties at low current density area.For Rack PlatingNC ZINC S-100S-100 MU : 6 ml/l, CM : 4 ml/lHL : 0.5 ml/l*Nice in plating appearance and good in chromating finish. *As chelating agent free, removal of heavy metals at waste water treatment is easy.*Applicable at high current, and excellent post-processing effects.NC ZINC 90A : 1 ml/l, B : 3 ml/l*Wide brightness range and excellent brightness and leveling. *Easy bath maintenance and excellent film physical properties. *Can be applied to both rack plating and barrel plating.BRIGHTENER FOR CYANIDE BATHApplication Trade Name Composition FeatureFor Barrel PlatingZINC LIGHT K-2500ZINC LIGHT K-75002 ml/l2 ml/l*Excellent brightness at low current density area and good dissolution. *For low and half strength cyanide baths.*Excellent brightness and leveling, wide workable bath temperature range, and excellent brightening effects at current density area. *Applicable from low to full strength cyanide baths.For Rack PlatingDUO ZINC 100ZINC LIGHT S-34002 ~ 5 ml/l3 ml/l*Wide brightness range and workable range, and excellent brightness and covering power. *For half and full strength cyanide bath, and applicable to barrel bath.*Excellent brightness, fast brighening effects and wide brigheness range. *Applicable to low, half and full strength cyanide baths.MIST PREVENTING AGENT FOR ALKALINE ZINC PLATINGApplication Trade Name Composition FeatureNC ZINC MIST0.2 ~ 1 ml/lMist Preventing AgentZINC MIST0.5 ~ 2 ml/lBRIGHTENER FOR ACID TYPE CYANIDE-FREE BATH*For alkaline cyanide-free bath. *Prevent mist scattering completely by small addition.*For cyanide bath, and prevent mist scattering completely by small addition.Application Trade Name Composition FeatureZINC NH1 : 30 ml/l, 2 : 1.5 ml/l*For barrel bath and solvent-free ammonium chloride bath. *Excellent brightness and leveling, and soft in plating film.Acid BathZINC A-100, A-200ZINC ACKA-100 : 30 ml/l, A-200 : 1 ml/l1 : 30 ml/l, 2 : 2 ml/l*For both rack and barrel plating baths, and for common use bath of ammonium chloride and potassium chloride. *Low running costs and economical.*For barrel plating bath and for ammonia-free potassium bath. *Excellent brightness and leveling.ZINC A1 : 30 ml/l, 2 : 1 ml/l*For both rack and barrel plating baths, and for common use bath of ammonium chloride and potassium chloride. *Induce properties of each bath maximally.
Change language