AutoHelm ST 2000 Plus - Comcast.net

More documents

Recommendations

Info

34 ST1000 Plus & ST2000 Plus Tiller Pilots - Owner’s HandbookCabling guidelines• consider how you will run cables to and from each component• avoid running cables through bilges where possible• avoid running cables close to fluorescent lights, engines, radiotransmitting equipment etc.4 Installing the Tiller PilotEMC installation guidelinesAll Raymarine equipment and accessories are designed to the bestindustry standards for use in the recreational marine environment.Their design and manufacture conforms to the appropriateElectromagnetic Compatibility (EMC) standards, but correctinstallation is required to ensure that performance is not compromised.Although every effort has been taken to ensure that they will performunder all conditions, it is important to understand what factors couldaffect the operation of the product.The guidelines given here describe the conditions for optimum EMCperformance, but it is recognized that it may not be possible to meetall of these conditions in all situations.To ensure the best possible conditions for EMC performance withinthe constraints imposed by any location, always ensure the maximumseparation possible between different items of electrical equipment.For optimum EMC performance, we recommend that:• Raymarine equipment and cables connected to it are:• At least 3 ft (1 m) from any equipment transmitting or cablescarrying radio signals e.g. VHF radios, cables and antennas.In the case of SSB radios, increase the distance to 7 ft (2 m).• More than 7 ft (2 m) from the path of a radar beam. A radarbeam can normally be assumed to spread 20 degrees aboveand below the radiating element.• The equipment is supplied from a separate battery from that usedfor engine start. Voltage drops below 10 V, and starter motortransients, can cause the equipment to reset. This will not damagethe equipment, but may cause the loss of some information andmay change the operating mode.• Raymarine specified cables are used. Cutting and rejoining thesecables can compromise EMC performance and must be avoidedunless doing so is detailed in the installation manual.
Chapter 4: Installing the Tiller Pilot 35• If a suppression ferrite is attached to a cable, this ferrite should notbe removed. If the ferrite needs to be removed during installationit must be reassembled in the same position.EMC suppression ferritesWe supply the fluxgate compass and power cables with suppressionferrites fitted. Always use these ferrites supplied by Raymarine.D3548-2Connections to other equipmentIf your Raymarine equipment is to be connected to other equipmentusing a cable not supplied by Raymarine, a suppression ferrite MUSTalways be attached to the cable near to the Raymarine unit.4 Installing the Tiller Pilot
Page 1 and 2: ST1000 Plus &ST2000 PlusTiller Pilo
Page 3 and 4: PrefaceiiiContentsChapter 1: Introd
Page 5 and 6: Chapter 1: Introduction 1Chapter 1:
Page 7 and 8: Chapter 1: Introduction 31.3 About
Page 9 and 10: Part 1:Using theTiller PilotPart 1:
Page 11 and 12: Chapter 2: Using the Tiller Pilot 7
Page 31 and 32: Chapter 3: Maintenance & Fault Find
Page 33 and 34: Chapter 3: Maintenance & Fault Find
Page 35 and 36: Part 2:Installing theTiller PilotPa
Page 37: Chapter 4: Installing the Tiller Pi
Page 41 and 42: Chapter 4: Installing the Tiller Pi
Page 55 and 56: Chapter 5: Commissioning the Tiller
Page 65 and 66: Chapter 6: Adjusting Tiller Pilot S
Page 71: ST1000+ and ST2000+tiller drives: s
Page 74 and 75: 70 ST1000 Plus & ST2000 Plus Tiller
Page 76: Factory Service CentersUnited State

AutoHelm ST 2000 Plus - Comcast.net

Create successful ePaper yourself

Delete template?

Save as template?