AutoHelm ST 2000 Plus - Comcast.net

More documents

Recommendations

Info

48 ST1000 Plus & ST2000 Plus Tiller Pilots - Owner’s HandbookIf required, the tiller pilot can be wired to the SeaTalk bus using asuitable SeaTalk interface cable (part numbers: D229 flat mouldedplug, D179 male round plug, D181 female round plug).Connect the SeaTalk cable to the tiller pilot socket as shown below.As well as sharing SeaTalk data, the tiller pilot can also be used tosupply power to the SeaTalk instruments.Raymarine produce a range of SeaTalk accessory cables you can useto connect the tiller pilot to SeaTalk instruments and control units:• flat plugs for recent SeaTalk equipment (e.g. ST30, ST40, ST60)• round plugs for older SeaTalk equipment (e.g. ST50)Extension cables - flat moulded plugs at each endPart no. Type LengthD284 Flat moulded plugs at each end 1 m (3 ft 3 in)D285 Flat moulded plugs at each end 3 m (9 ft 10 in)D286 Flat moulded plugs at each end 5 m (16 ft 5 in)D287 Flat moulded plugs at each end 9 m (29 ft 6 in)D288 Flat moulded plugs at each end 20 m (65 ft 6 in)Conversion cables - flat moulded plug to round plugPart no. Type LengthD187 Flat moulded plug to male round plug 0.15 m (6 in)D188 Flat moulded plug to female round plug 0.3 m (12 in)Extension cables - round plugs at each end4 Installing the Tiller PilotPart no. Type LengthD124 Male round plug to female round plug 1 m (3 ft 3 in)D125 Male round plug to female round plug 3 m (9 ft 10 in)D126 Male round plug to female round plug 6 m (19 ft 8 in)D154 Male round plug to female round plug 9 m (29 ft 6 in)Interface cables - flat moulded/round plug to bare endsPart no. Type LengthD229 Flat moulded plug to bare ends 1 m (3 ft 3 in)D179 Male round plug to bare ends 3 m (9 ft 10 in)D181 Female round plug to bare ends 3 m (9 ft 10 in)D5554-1
Chapter 4: Installing the Tiller Pilot 49Remote control cablingIf required, you can operate the tiller pilot using:• a full-function ST600R remote control unit (part no: A12016), or• a SeaTalk hand-held remote control (part no: Z101)The following illustration shows how to connect a remote control.Supply (0 V)Socket12 A fuseSeaTalkinstrumentsSupply (+12 V DC)Yellow (SeaTalk data)Screen (SeaTalk 0 V)Red (SeaTalk 12 V)with 5 A fuseSeaTalk cableSeaTalkcable*SeaTalksocketST600R remoteZ101 remoteor*If you only need to connect a remote, wirethis SeaTalk cable into the tiller pilot socketD3279-2NMEA cablingIf required, you can connect a NMEA navigator or wind instrument tothe tiller pilot. It can then use this information for Track andWindTrim modes.Recognized NMEA dataThe following table lists the recognized NMEA sentences.4 Installing the Tiller Pilot
Page 1 and 2: ST1000 Plus &ST2000 PlusTiller Pilo
Page 3 and 4: PrefaceiiiContentsChapter 1: Introd
Page 5 and 6: Chapter 1: Introduction 1Chapter 1:
Page 7 and 8: Chapter 1: Introduction 31.3 About
Page 9 and 10: Part 1:Using theTiller PilotPart 1:
Page 11 and 12: Chapter 2: Using the Tiller Pilot 7
Page 31 and 32: Chapter 3: Maintenance & Fault Find
Page 33 and 34: Chapter 3: Maintenance & Fault Find
Page 35 and 36: Part 2:Installing theTiller PilotPa
Page 37 and 38: Chapter 4: Installing the Tiller Pi
Page 51: Chapter 4: Installing the Tiller Pi
Page 55 and 56: Chapter 5: Commissioning the Tiller
Page 65 and 66: Chapter 6: Adjusting Tiller Pilot S
Page 71: ST1000+ and ST2000+tiller drives: s
Page 74 and 75: 70 ST1000 Plus & ST2000 Plus Tiller
Page 76: Factory Service CentersUnited State

AutoHelm ST 2000 Plus - Comcast.net

Create successful ePaper yourself

Delete template?

Save as template?