DTHC-SETUP/INSTALL MANUAL CandCNC

More documents

Recommendations

Info

<strong>INSTALL</strong>ATION OF CURRENT TRANSFORMERUsed for plasma units that do not haveArc Good (Arc Xfer) signal or DCPProvided Power Resistoracross terminalsWires to ARC OKAYscrew terminals onTHC Sensor Card35 to 100A range Plasma unitsPass one conductor from the AC line straightthrough the center of the Current TransformerProvided Power Resistoracross terminalsWires to ARC OKAYscrew terminals onTHC Sensor CardLess than 35A UnitsTake a full wrap with one wire fromthe AC line.PAGE 18
Digital Current Probe Model DCP-01Physical install and hookupDCP-01 Digital Current Probel uses theexisting THC SENSOR (rev14 or above)and slips over the Plasma SystemWorkclamp lead wire to provide DC ampfeedback to the <strong>DTHC</strong> and to the MACHscreen. The following series of photosshows the DCP being hooked up to aplasma cutter.Start by removing the ground clamp fromyour plasma workclamp. If it has a large ringterminal on the end where it attaches to theclamp you will need remove the ring terminaland replace it with a new one after you pushit through the DCP unit.Loosen the cable strain relief/clamps on eachend of the box by twisting the retainer nutcounterclockwise viewed from the end. TheStrain relief has an internal collar that clampsdown on the wire the more it is tightened.Straighten the wire as much as possible andstart feeding it from the right hand side.Plasma Unit EndClamp EndRight hand Strain ReliefClamp End Plasma Unit EndLeft hand Strain ReliefCable passes through center of DCP-01Push the wire through gently. If it hangs tryrotating the wire and pushing but do notforce it. There is a round hole in the Hallprobe inside the box that the wire has topass through. It is located close to the rightside of the unit. If you have problems gettingthe wire to go though pull the wire out andremove the 4 screws holding the top andremove the top and the PCB with the HallProbe (see next page). Thead the wirethough the right side strain relief and pullenough through so you can thread the HallProbe on the card and then over and out ofthe left side strain relief.PAGE 19
Page 1 and 2: DTHC-SETUP/INSTALLMANUALREV5JAN 201
Page 4 and 5: PRELIMINARY TESTING THE DTHC MODULE
Page 6: J15TipVoltsWorkclamp+ [POS]L4R7- [N
Page 12 and 13: HYPERTHERM PowerMAX 45Connecting TH
Page 14 and 15: THC SENSOR CARD TESTINGBefore you m
Page 16 and 17: 1. Most plasma units have connectio
Page 20 and 21: Workclamp Lead Wire goesthrough Hal
Page 22 and 23: 2. Start MACH3 on the controller PC
Page 24 and 25: DTHC EXPANION MODULE. Locatedabove
Page 26 and 27: PC w/MACH3Grounding practices to re
Page 28 and 29: SETTING UP YOUR Z AXIS FOR AUTOMATI
Page 30 and 31: PAGE 30
Page 32 and 33: MP3000-DTHC Screen SectionThe follo
Page 34 and 35: ALTERNATE SCREEN SET FOR SMART-KUTU
Page 36 and 37: To Adjust PRESET Volts (andheight)
Page 38 and 39: CURRENT SETTINGS BUTTON: Shows the
Page 40 and 41: INFORMATION GROUP:The Information s
Page 42 and 43: TIP SAVER %: This value determines
Page 44 and 45: GENERAL THC SETTINGSThe General THC
Page 46 and 47: FINAL TESTINGDoing a startup test u
Page 48 and 49: Kerf width: Sets the width offset u
Page 50 and 51: 10. Torch oscillates wildly UP andD
Page 52: RAW ARC VOLTAGEPLASMA UNITTORCH SWI

DTHC-SETUP/INSTALL MANUAL CandCNC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?