2006 Ford Racing Performance Parts Catalog
2006 Ford Racing Performance Parts Catalog
2006 Ford Racing Performance Parts Catalog
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
28-TOOTH 8.8" TRACTION-LOK REAR AXLE ASSEMBLIES<br />
(LESS BRAKES AND SHAFTS)<br />
FEATURES…<br />
• Approximately 35% stronger than the<br />
production 7.5" axle<br />
• Units are fully assembled with housing<br />
(including all applicable brackets),<br />
gearset and 28-tooth traction-lok differential<br />
• Bolts into the “Fox” vehicles listed with each<br />
part number that were originally equipped<br />
with 7.5" axle<br />
• Axle assembly uses vehicle’s 28-tooth<br />
axle shafts and rear drum brakes<br />
C-CLIP ELIMINATOR (8.8" AXLES)<br />
M-4220-A<br />
• Retains axle externally<br />
• Eliminates need for C-Clips at differential<br />
• Mandatory for spools and wherever required by sanctioning bodies<br />
• Fits axle shafts with 1.400" dia. bearing journal<br />
• Not recommended for road racing applications or rear disc brakes<br />
AXLE GIRDLE<br />
M-4033-G1 8.8" <strong>Ford</strong><br />
• Lightweight 356T6 aluminum casting<br />
replaces rear cover on 8.8"<br />
• Load bolts provide additional support<br />
for differential bearing caps<br />
• Increase ring and pinion gear life<br />
• Stud kit M-4034-A recommended<br />
for 8.8" and Dana 60<br />
NOTES: Check exterior clearance<br />
to chassis/suspension. Will not fit 2005<br />
Mustang<br />
*Not legal for sale or use on pollution-controlled motor vehicles. **Direct replacement part.<br />
M-4006-B373 shown<br />
8.8" TRACTION-LOCK REBUILD KIT<br />
M-4700-B<br />
• Kit includes clutch pack, shims, friction<br />
modifier and instruction sheet<br />
• Fits all 8.8" Traction-Lok differentials<br />
8.8" AXLE INSTALLATION KIT<br />
M-4050-B<br />
This kit consists of 2 bushings, 2 C-locks and 1 4-oz. bottle<br />
of friction modifier. These parts are included with every <strong>Ford</strong> <strong>Racing</strong><br />
8.8" axle assembly. Now available separately in this kit, in response<br />
to requests from racers and fabricators. 8.8" FORD/DANA 60 BEARING CAP<br />
STUD KIT<br />
M-4034-A<br />
This kit provides studs for increased retention of the differential caps<br />
on 8.8" <strong>Ford</strong> and Dana 60 axles. They were designed for use with the<br />
M-4033-G girdles but can be used with the stock covers.<br />
2003-04 COBRA PINION FLANGE<br />
M-4851-B<br />
• Original equipment on<br />
2003-04 Mustang Cobra<br />
• Designed for use with<br />
1350 U-joint flange<br />
• 4.25" bolt circle<br />
• Fits all 8.8" rear drive pinions<br />
PART NUMBER RATIO VEHICLE APPLICATION<br />
M-4006-B355* 3.55:1 1979-98 Mustang ➀ 1981-82 Granada/Monarch<br />
1979-86 Capri 1983-85 LTD/Marquis<br />
M-4006-B373* 3.73:1 1978-82 Fairmont/Zephyr<br />
NOTE: ➀ 1986-95 Mustang 5.0L vehicles are factory-equipped with 28-tooth 8.8" axle assembly.<br />
www.fordracingparts.com 141<br />
CHASSIS<br />
COMPONENTS