XPP-721 Personal Pipettor GUI Software Operation Manual - FluidX

More documents

Recommendations

Info

When editing a protocol by right-clicking a command, additional editing functions areavailable. The “Move To” function moves one command line from its original position toanother position in the protocol. Right click the line to be moved and select Move To.Right click on the command line under which the line to be moved is to be inserted. The“Move To” function in the menu will become “Move Here”. Select “Move Here”, theoriginal command line will now be inserted under the selected target line.o To Insert a new line between lines – In panel 6 of status bar, click text Add onceand it will turn into Insert. Click one line below which the new line should beinserted into, and create a new command that will be added below the selectedline.o To Edit a line in the Protocol window – highlight the line to be edited, thecommand parameters will then be displayed on the right-hand side of the screenand can now be edited.10. Run ProtocolThe Execution commands control the flow of protocol. The user may run the protocolcompletely automatically or run each line manually, stop a protocol, pause a protocoland choose the number of loop cycles for a protocol. There are two ways to run theprotocol, Run and Run Step.1). To run the entire protocol, click Run. If Run Check is set to true inConfig tab, a Confirm window will appear.It’s important to visually verify that the head and plates/Spacers matchwhat are actually in the Confirm window. Mismatching of the headand plates may cause serious damage. Head and Plate and Spacer (ifused) check boxes must be checked for the protocol to run.2). To run a single line of a protocol, highlight the line in the protocolwindow and click Run Step.3
o In the event that the tips are not empty (liquid remaining from a previous run),and Run is clicked, a message “Empty Tips First” will appear. Click button(Empty Tips) in the tool bar until the tips are empty. Then run protocol.Caution: If not select to empty tips in wash station, make sure a container isprepared to catch the liquid from the tips.o When the STOP button is clicked, a message is displayed, select Yes to terminateprogram, select No to continue running the program. The STOP button can alsobe used to pause a program. The program will be paused until No is selected inthe message window.o Several lines of a protocol may also be executed. Before running the protocol,check the boxes to the left of the commands to be executed. All checkedcommands will be executed but unchecked commands will not.o To run a protocol more than once, set the cycle times by using up/down arrow ortyping in a number before running the protocol or during the period to run theprotocol.11. Set Parameters1) Common ParametersSelect the Config tab on the display window to show the common parameters table.The left column shows the parameter name, the middle column shows the parametervalue (that can be edited), the right column shows the parameter unit and can alsorestore the default value for the parameter if clicked.3
Page 2 and 3: NoticesThe information contained in
Page 4 and 5: 1. Operation OverviewTurn On Pipett
Page 6 and 7: 4. Program InitializationWhen the A
Page 8 and 9: 1. Title bar - Shows new file or th
Page 10 and 11: 6.2 Select Pipetting HeadSelect an
Page 12 and 13: align the tips to the centre and to
Page 14 and 15: eing used in the main window. If yo
Page 17 and 18: 8. Creating ProtocolsAfter populati
Page 19 and 20: 8.2 Edit ParameterWhen creating a n
Page 21 and 22: o Airgap and Volume: Select the app
Page 23 and 24: o Depth: Drag the tip depth slider
Page 25 and 26: o Single Row: When a single row 12C
Page 27 and 28: o For dispensing small volumes of l
Page 29 and 30: o Input the wash Volume required (a
Page 31 and 32: o A target station is selected in t
Page 33 and 34: o Input the Airgap and aspirate Vol
Page 35 and 36: The Source Station for aspiration i
Page 37: There is a group of buttons for edi
Page 41 and 42: 2. Special ParametersThe special pa
Page 43 and 44: Set Variable - Variables can be set
Page 45 and 46: Reset pipettor. The same as clickin
Page 47: Apricot Designs, Inc.825 S. Primros

XPP-721 Personal Pipettor GUI Software Operation Manual - FluidX

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?