xxx-nt sport owner! - Losi

More documents

Recommendations

Info

BAG C (Continued)Figure 357372Step 23. Locate the slipper shaft (73) and thread the 4-40 x 1" setscrew(72) all the way into the threaded side of the slipper shaft (73). Makesure that the setscrew (72) is TIGHT!*NOTE: Some top gear/slipper shaft assemblies may be preassembledfrom the factory.Tip: A small amount of liquid thread-lock should be used to help tohold the setscrew securely in place. If your slipper shaft was preassembledat the factory, thread-lock compound has already beenapplied.72Figure 35Figure 3674Step 24. Press the 1/16" x 5/16" pin (74) into the small hole in theslipper shaft (73) so that it extends evenly from both sides of the shaft(73).Step 25. Slide the top gear (75) over the setscrew (72) onto the slippershaft (73). Align the groove in the gear (75) with the pin (74) and slidethe gear (75) over the pin (74).Step 26. Secure the top gear (75) to the shaft (73) by inserting a 3/16"C-clip (76) into the groove in the slipper shaft (73).7676737475Figure 36Figure 377918176 7876Step 27. Locate the brake shaft (77) and press the .078" x 3/8" spirolpin (78) into the small hole away from the grooved end of the brakeshaft (77) so that it extends evenly from both sides of the shaft (77).Step 28. Press the compound gear bushing (181) all the way into theend of the compund gear (79). Slide the compound gear (79), with thebushing (181) in place, over the brake shaft (77). Align the groove inthe gear (79) with the pin (78) and slide the gear (79) over the pin (78).Step 29. Secure the compound gear (79) and bushing (181) to theshaft (77) by inserting a 3/16" C-clip (76) into the groove in middle ofthe brake shaft (77).7877Figure 3715
BAG C (Continued)Figure 3880 8280 81Step 30. Insert two 3/16" x 3/8" sealed bearing (80) into the two topbearing seats of the right gearbox half (82).*NOTE: If any of the supplied gearbox bearings only have oneTeflon seal(colored, woven looking) in it, position the seal to theoutside of the gearbox half.Step 31. Insert a 1/2" x 3/4" bearing (81) into the lowerbearing seat of the right gearbox half (82).81Figure 38Figure 3983PRE-TAPTHESE HOLES80 81Step 32. Use the short, 4-40 thread-cutting screw included in thewrench bag to pre-tap the three holes noted in Figure 39. Thread thescrew all the way into and out of each hole.Step 33. Insert two 3/16" x 3/8" sealed bearing (80) into the two topbearing seats of the left gearbox half (83).Step 34. Insert a 1/2" x 3/4" bearing (81) into the lowerbearing seat of the left gearbox half (83).8180Figure 39Figure 4084Step 35. Slip the 3/16" x .015 shim (84) over the slipper shaft (73) upagainst the top gear (75).Step 36. Insert the slipper shaft (73) into the forward-most bearing(80) in the left gearbox half (83).8380847573Step 37. Insert the differential assembly into the 1/2" x 3/4" bearing(81) in the right gearbox half (82). Insert the differential diff nut carrier(57) side first.*NOTE: be sure the head of the diff adjusting screw faces theright side of the gearbox. This will allow easy adjustment whilerunning your truck.8164Figure 4016
Page 1 and 2: Carefully read through all instruct
Page 3 and 4: RADIO/ELECTRICALRefer to the includ
Page 5 and 6: BAG A (Continued)Figure 41713 16 17
Page 7 and 8: BAG A (Continued)Figure 817 2323Ste
Page 9 and 10: BAG A (Continued)Figure 1420Step 26
Page 11 and 12: BAG B (Continued)Figure 179 17 3834
Page 13 and 14: BAG B (Continued)Figure 21212153Ste
Page 15 and 16: BAG CFigure 267577Step 1. Insert a
Page 17: BAG C (Continued)Figure 33636163 61
Page 21 and 22: BAG C (Continued)Figure 4393 94 95S
Page 23 and 24: BAG C (Continued)Figure 46Step 59.
Page 25 and 26: BAG DFigure 511710617Attach the dog
Page 27 and 28: BAG D (Continued)Figure 56122Step 1
Page 29 and 30: BAG D (Continued)Figure 60123Step 2
Page 31 and 32: BAG E (Continued)Figure 64134133Ste
Page 33 and 34: BAG E (Continued)Figure 6895 142331
Page 35 and 36: ENGINE INSTALLATIONNOTE: The follow
Page 37 and 38: ENGINE INSTALLATION (Continued)Figu
Page 43 and 44: RADIO INSTALLATIONFigure 90Step 1.
Page 45 and 46: RADIO INSTALLATION (Continued)Figur
Page 47 and 48: RADIO INSTALLATION (Continued)Rotar
Page 49 and 50: RADIO INSTALLATION (Continued)Rotar
Page 55 and 56: FINAL ASSEMBLYFigure 114Step 1. Tri
Page 57 and 58: ATTACHING THE RECEIVER to the cente
Page 59 and 60: SPARE PARTS LISTKEY # KIT/PART DESC
Page 61 and 62: SPARE PARTS LISTKEY # KIT/PART DESC
Page 63 and 64: Driver:Date:Setup SheetTrack:! Indo

xxx-nt sport owner! - Losi

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?