xxx-nt sport owner! - Losi

More documents

Recommendations

Info

ENGINE INSTALLATION (Continued)Figure 8830Step 36. Cut an 11" (280mm) length of fuel tubing (176) from the piecesupplied.Step 37. Cut one end of the 11" piece of tubing at a 45 o angle as shownin Figure 88A. Install the uncut side of the tubing to the forwardfitting on the top of the fuel tank (30).Step 38. Wind the tubing into two small loops and insert them into therectangular slot in the chassis brace (29) as shown. Insert the cut endof the tubing into the inside (small) hole in the tuned pipe (176). Thisfuel line will serve as the fuel tank pressure line.175IMPORTANT NOTE: Make sure that the cut section of fueltubing is inserted all the way into the tuned pipe.176Figure 88Figure 88ACUTFigure 8930Step 41. Attach one end of the fuel tubing (176) to the rear fitting onthe top of the fuel tank (30), and attach the other end to the fitting onthe carburetor. This will be your fuel line.176Figure 8939
RADIO INSTALLATIONFigure 90Step 1. Cut a piece of two-sided tape (182) to the same size as thebottom of the receiver. Remove the backing from one side of the tape(182) and attach the tape (182) to the bottom of the receiver.Tip: For best results clean the surfaces that the two-sided tape willbe attached to with a mild rubbing alcohol. This will ensure agood, strong bond. Allow the surface to fully dry before attachingthe tape.Step 2. Remove the backing from the remaining side of the two-sidedtape (182) and attach the receiver to the side of thecenter chassis brace (29), between the two receiver box guide rails asshown. The receiver should be mounted so that it is at least 1/8"above the chassis (19) and the antenna is to the front of the truck.Step 3. Plug the steering servo into the slot marked "Channel 1" or"Function 1" on the receiver.18229Figure 90Figure 91184Step 4. Route the antenna wire up, through the antenna mountingpost in the center chassis brace (29).Step 5. Slide the antenna wire through the antenna tube (183) (a smalldrop of oil in the tube will make this easier).Step 6. While pulling the wire through the antenna tube (183), slidethe antenna tube (183) down and push it firmly into the antennamounting post on the center chassis stiffener (29).Step 7. Fold the wire over the antenna tube (183) and place the antennacap (184) over the tube (183) and extra wire.*NOTE: If the antenna wire is shorter than the tube, remove thetube and cut enough off of the tube so that the wire will extend about3/4" past the end of the tube.18329Figure 9140
Page 1 and 2: Carefully read through all instruct
Page 3 and 4: RADIO/ELECTRICALRefer to the includ
Page 5 and 6: BAG A (Continued)Figure 41713 16 17
Page 7 and 8: BAG A (Continued)Figure 817 2323Ste
Page 9 and 10: BAG A (Continued)Figure 1420Step 26
Page 11 and 12: BAG B (Continued)Figure 179 17 3834
Page 13 and 14: BAG B (Continued)Figure 21212153Ste
Page 15 and 16: BAG CFigure 267577Step 1. Insert a
Page 17 and 18: BAG C (Continued)Figure 33636163 61
Page 19 and 20: BAG C (Continued)Figure 3880 8280 8
Page 21 and 22: BAG C (Continued)Figure 4393 94 95S
Page 23 and 24: BAG C (Continued)Figure 46Step 59.
Page 25 and 26: BAG DFigure 511710617Attach the dog
Page 27 and 28: BAG D (Continued)Figure 56122Step 1
Page 29 and 30: BAG D (Continued)Figure 60123Step 2
Page 31 and 32: BAG E (Continued)Figure 64134133Ste
Page 33 and 34: BAG E (Continued)Figure 6895 142331
Page 35 and 36: ENGINE INSTALLATIONNOTE: The follow
Page 37 and 38: ENGINE INSTALLATION (Continued)Figu
Page 39 and 40: ENGINE INSTALLATION (Continued)Figu
Page 41: ENGINE INSTALLATION (Continued)Figu
Page 45 and 46: RADIO INSTALLATION (Continued)Figur
Page 47 and 48: RADIO INSTALLATION (Continued)Rotar
Page 49 and 50: RADIO INSTALLATION (Continued)Rotar
Page 55 and 56: FINAL ASSEMBLYFigure 114Step 1. Tri
Page 57 and 58: ATTACHING THE RECEIVER to the cente
Page 59 and 60: SPARE PARTS LISTKEY # KIT/PART DESC
Page 61 and 62: SPARE PARTS LISTKEY # KIT/PART DESC
Page 63 and 64: Driver:Date:Setup SheetTrack:! Indo

xxx-nt sport owner! - Losi

Create successful ePaper yourself

Delete template?

Save as template?