Prestige SOLO 110.pdf - Bloom Lake Farms

More documents

Recommendations

Info

Boiler PipingTo theSystem12912"Max.From the System810 11 47771 1 11. PRESTIGE Solo boiler2. Boiler circulator3. Flow/check valve4. Isolation valve6. Drain/purge valve7. Pressure relief valve8. Air separator9 Automatic air vent10. Diaphragm expansion tank11. Automatic fill valve12. System circulator624 4 43 3 34 4462 26Fig. 14: Multiple <strong>Prestige</strong> Boiler Piping - Primary / Secondary / Piping using Balanced Manifold System24
Installing Vent/ Combustion Air & CondensateSECTION V - Installing Vent /Combustion Air & Condensate DrainInstalling Vent and Combustion AirDANGERThe PRESTIGE Solo must be ventedand supplied with combustion air asshown in the PRESTIGE Solo VentSupplement, included in the boilerinstallation envelope. Refer to optionalvent kit instructions for additional ventinstallation instructions. Once installationis completed, inspect the vent andcombustion air system thoroughly toensure systems are airtight and complywith the instructions given in the ventingsupplement and are within all requirementsof applicable codes. Failure tocomply with the installation requirementson the venting and combustion airpiping will cause severe personal injuryor death.Installing Condensate Drain Assembly1. Locate the condensate drain assembly andinstall as shown in Fig. 15 page 26.NOTICEThe installer may want to fill the condensatetrap with water prior to assemblingon the unit.2. Remove the retaining nut and rubber sealfrom the condensate drain assembly andslide over the heat exchanger condensatedrain nipple. Connect the condensate drainassembly to the retaining nut and tighten.Hand tight only!WARNINGEnsure the condensate drain assemblycontains the plastic seated ball. Do notinstall the condensate drain assembly ifthe ball is lost or missing, replace theentire assembly.3. Remove the compression nut and rubberseal from the drain outlet.4. Using 3/4” x 2’ flexible PVC tube provided,slide the compression nut and rubberseal over the pipeNOTICEThe use of 3/4” PVC or CPVC pipe isalso acceptable. If 3/4” pipe is useddeburr and chamfer pipe to allow matingonto the drain assembly.5. Thread the rubber seal into the compressionnut to ease installation of the pipe tothe drain assembly.6. Seat the pipe onto the drain assembly andtighten the compression nut. Hand tightonly!NOTICEThe installer may opt to using 13/16" IDtubing in lieu of rigid piping.NOTICEThe drain line materials must be anapproved material by the authority havingjurisdiction. In absence of suchauthority, PVC and CPVC piping mustcomply with ASTM D1785 or D2845.The cement and primer used on the pipingmust comply with ASME D2564 orF493. For installations in Canada, useCSA or ULC certified PVC or CPVCpipe, fittings and cement/primer.25
Page 2 and 3: Table of ContentsPRODUCT AND SAFETY
Page 5 and 6: Table of ContentsAccessing Boiler I
Page 7 and 8: Product & Safety InformationDefinit
Page 9 and 10: Pre-Installation ItemsSECTION I - P
Page 11 and 12: Combustion Air and VentingSECTION I
Page 13 and 14: Combustion Air and VentingMethods o
Page 15 and 16: Combustion Air and VentingOutdoor O
Page 17 and 18: Combustion Air and VentingCommonwea
Page 19 and 20: Unit Preparations4. Remove the brac
Page 21 and 22: Boiler PipingPressure Relief Valve(
Page 23 and 24: Boiler PipingConnect the expansion
Page 25 and 26: Boiler PipingSystem Piping - Zone V
Page 27 and 28: Boiler Piping453AdditionalZone Load
Page 29: Boiler Piping45AdditionalRadiant Zo
Page 33 and 34: Gas PipingSECTION VI - Gas PipingGa
Page 35 and 36: Gas PipingPROPANE GASPipe Sizing -
Page 37 and 38: Internal WiringSECTION VII - Intern
Page 39 and 40: External WiringSECTION VIII- Extern
Page 41 and 42: External Wiring4 Wire Zone ValveZon
Page 43 and 44: Start-Up PreparationSECTION IX - St
Page 45 and 46: Start-Up PreparationCheck For Gas L
Page 47 and 48: Start-Up ProceduresccWARNINGVenting
Page 49 and 50: Start-Up ProceduresSet Boiler CH Ta
Page 51 and 52: Start-Up ProceduresBoiler Control D
Page 53 and 54: Start-Up ProceduresSetting The Boil
Page 55 and 56: Start-Up ProceduresError (Hard Lock
Page 57 and 58: Outdoor Reset ControlSummer / Winte
Page 59 and 60: Outdoor Reset Control180Boiler Temp
Page 61 and 62: Factory Setting ParametersFactory S
Page 63 and 64: Installation RecordSECTION XIV - In
Page 65 and 66: Maintenance ProceduresSECTION XVI -
Page 67 and 68: Maintenance ProceduresCheck Expansi
Page 69 and 70: Maintenance ProceduresCheck Flame S
Page 71 and 72: Replacement Parts7659253Fig. 26: PR
Page 73 and 74: Replacement PartsFig. 28: PRESTIGE
Page 75 and 76: Product Specifications15.43” [392
Page 77 and 78: Products SpecificationsBoilerModelF
Page 79: Additional Quality Water Heating Eq

Prestige SOLO 110.pdf - Bloom Lake Farms

Create successful ePaper yourself

Delete template?

Save as template?