Prestige SOLO 110.pdf - Bloom Lake Farms

More documents

Recommendations

Info

Outdoor Reset ControlCH Reset Curve Warmest Day(Parameter 12)This parameter is not applicable if an outdoorsensor is not connected to the boiler. When anoutdoor temperature sensor is connected, theCH Reset Curve Warmest Day is the warmestdesign temperature of the heating system.Entering MCBA Access CodeThe installer must enter the MCBA AccessCode to adjust the advanced parameter settingsof the MCBA. The Access Code can beentered as follows:1. Press the MODE button until the displayshows STbY.2. Press and hold the MODE and STEP buttonstogether for 2 to 3 seconds until thedisplay shows CODE.3. Press the STEP button once and the displaywill show C_XX where XX represents arandom number.4. Press the “+” or “–“ buttons to change thenumber displayed to read C_54.. Press andhold the “+” or “–“ button to rapidlychange the number.5. When the display reads C_54, press theSTORE button to save the Access Code.The display should flash to indicate that theAccess Code was saved.After the Access Code has been entered, theadvanced parameters can be accessed by pressingthe MODE button until the display showsPARA. Once the display shows PARA, pressthe STEP button to reach the appropriate parameter.The display should follow the followingsequence:Press STEP once- 1140Press STEP x2 - 2_01Press STEP x3 - 3_01Press STEP x4 - 4186Press STEP x5 - P_10Press STEP x6 - P_11Etc......After Parameter 4, the display will show P followedby the parameter number. Once a particularparameter is reached, the display willchange to show the current setting of that parameter.NOTICEThe actual parameter values displayedon the display may vary depending onthe application, but the sequence willalways occur in the order shown.Changing a Parameter Setting1. Use the “+” or “–“ button to change theparameter setting.2. Press the STORE button to save thechange. The display should flash to indicatethat the change was saved.3. Press the RESET button to leave the AccessCode mode.52
Outdoor Reset Control180Boiler Temperature ( F)140100866020Parameter 10Set PointParameter 12 SettingParameter 4 Set PointParameter 11 Setting90706450 30 10 0 -10Outdoor Air Temperature ( F)Graph 1: Outdoor Air Temperature Reset Curve (Example)Table 3: Outdoor Air Temperature Reset (Example)Graph 1 illustrates Parameter 4 adjusted to 140ºF target temperature at 0ºF outdoorair temperature.Note: Factory setting of Parameter 4 is 186ºF.53
Page 2 and 3:
Table of ContentsPRODUCT AND SAFETY
Page 5 and 6:
Table of ContentsAccessing Boiler I
Page 7 and 8: Product & Safety InformationDefinit
Page 9 and 10: Pre-Installation ItemsSECTION I - P
Page 11 and 12: Combustion Air and VentingSECTION I
Page 13 and 14: Combustion Air and VentingMethods o
Page 15 and 16: Combustion Air and VentingOutdoor O
Page 17 and 18: Combustion Air and VentingCommonwea
Page 19 and 20: Unit Preparations4. Remove the brac
Page 21 and 22: Boiler PipingPressure Relief Valve(
Page 23 and 24: Boiler PipingConnect the expansion
Page 25 and 26: Boiler PipingSystem Piping - Zone V
Page 27 and 28: Boiler Piping453AdditionalZone Load
Page 29 and 30: Boiler Piping45AdditionalRadiant Zo
Page 31 and 32: Installing Vent/ Combustion Air & C
Page 33 and 34: Gas PipingSECTION VI - Gas PipingGa
Page 35 and 36: Gas PipingPROPANE GASPipe Sizing -
Page 37 and 38: Internal WiringSECTION VII - Intern
Page 39 and 40: External WiringSECTION VIII- Extern
Page 41 and 42: External Wiring4 Wire Zone ValveZon
Page 43 and 44: Start-Up PreparationSECTION IX - St
Page 45 and 46: Start-Up PreparationCheck For Gas L
Page 47 and 48: Start-Up ProceduresccWARNINGVenting
Page 49 and 50: Start-Up ProceduresSet Boiler CH Ta
Page 51 and 52: Start-Up ProceduresBoiler Control D
Page 53 and 54: Start-Up ProceduresSetting The Boil
Page 55 and 56: Start-Up ProceduresError (Hard Lock
Page 57: Outdoor Reset ControlSummer / Winte
Page 61 and 62: Factory Setting ParametersFactory S
Page 63 and 64: Installation RecordSECTION XIV - In
Page 65 and 66: Maintenance ProceduresSECTION XVI -
Page 67 and 68: Maintenance ProceduresCheck Expansi
Page 69 and 70: Maintenance ProceduresCheck Flame S
Page 71 and 72: Replacement Parts7659253Fig. 26: PR
Page 73 and 74: Replacement PartsFig. 28: PRESTIGE
Page 75 and 76: Product Specifications15.43” [392
Page 77 and 78: Products SpecificationsBoilerModelF
Page 79: Additional Quality Water Heating Eq
show all

Prestige SOLO 110.pdf - Bloom Lake Farms

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?