Stratos HSSD-2 â¢ INSTALLER'S HANDBOOK

More documents

Recommendations

Info

1. Types ofDetector1.1 Standard DetectorThe Standard Detector may be operated as a stand-alone unit, or may be part of anetwork of detectors centrally monitored by a Command Module (see section 1.2).It may be programmed via the front panel as in the version shown above. Alternatively,and for detectors ordered without front panel display, the detector may be programmedremotely via the detector’s RS485 terminals using a Command Module, orvia the detector’s RS232 port using a PC running AirSense Technology’s remote controlsoftware. A copy of this software is packed with each detector supplied.1.2 Stand aloneCommand Module/Command ModuledetectorWhen multiple detectors are networked together, a Command Module may be usedto tie all the detectors together and to provide a central point for programming,running diagnostics and PC and fire panel connection.The Command Module can be mounted either inside a detector as shown or as astand-alone unit in its own housing without an aspirator or smoke detection circuitry.If detectors attached to the Command Module are mounted in different fire zonesthen the Command Module must be mounted in its own housing with separate powersupply to comply with BS5839 and EN54.When a Command Module is mounted inside a detector, the Standard Detector displayis replaced with a dedicated Command Module display. The programming buttons anddisplay on the front of the detector belong to the Command Module.Programming from the Command Module is very similar to programming a detector,the main difference being that the Command Module has extra functions to control allthe Stratos detectors connected to the detector loop.Page 4© AirSense Technology. 2009Stratos HSSD-2 • INSTALLER’S HANDBOOK • Iss. 10
1.3 StandardDetector interiorview894123106571. Terminal block connections (see section 5.3.1)2. RS485 terminal connections (see section 5.3.1)3. 24VDC power supply connections (see section 5.4.1)4. 1A 5 x 20mm T-type protection fuse5. Detector address DIP switch (see section 8.1)6. Front panel display connector7. Filter removal tab (see section 10)8. RS232 serial port (see section 8.5)9. Safety earth studs (see section 5.4)10. Display fixing screws (see section 5.2.1)Page 5Stratos HSSD-2 • INSTALLER’S HANDBOOK • Iss. 10© AirSense Technology. 2009
Page 1 and 2: High Sensitivity Smoke DetectorInst
Page 6 and 7: 1.4 Stand-alonecommand moduleinteri
Page 8 and 9: 2. Controls andIndicators65 8Standa
Page 10: 3. Programmingthe unitThe Stratos-H
Page 14 and 15: 3.4.2 Alarm levels (Numeric - Addre
Page 16 and 17: 3.4.9 Auto FastLearn enable / disab
Page 18 and 19: 3.4.19 Device Text (Alpha - Address
Page 20 and 21: 3.4.31 Chart log recording rate (Nu
Page 22 and 23: 3.4.38 Call centre (Numeric - CM on
Page 24 and 25: 3.5 Menu mapMenuSubmenu Item ParaMA
Page 26 and 27: NB ☞c. Maximum recommended total
Page 28 and 29: 5.2.1 Removal andreplacement of the
Page 30 and 31: 5.3.2Command Moduleterminal blockco
Page 32 and 33: 5.4 Power SupplyConnectionsThe dete
Page 34 and 35: 5.4.4 Backup batteriesThe Stratos-H
Page 36 and 37: The settings of a compliant system
Page 38 and 39: 6.1.4 Configuring the softwareNo ma
Page 40 and 41: 8.1.1 Address tableAddresses chosen
Page 42 and 43: 8.3 Connecting aCommand Moduleto an
Page 44 and 45: When multiple detectors are network
Page 46 and 47: As dust contained in the dust separ
Page 48 and 49: 11.6 Flow fault errors• These occ
Page 50 and 51: 13. Do’s and Don’ts DO✔✔✔
Page 52: 1 Caxton Place • Caxton Way • S

Stratos HSSD-2 â¢ INSTALLER'S HANDBOOK

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Stratos HSSD-2 â¢ INSTALLER'S HANDBOOK