Technical Appendix Specifications for the RADIO SYSTEM UPGRADE

More documents

Recommendations

Info

H. Comparator shall be capable of storing basic statistical data such as count and duration that aparticular receiver was selected; number of receiver or line failures, etc. Such data shall beavailable on a port using a PC.I. Comparator shall be capable of applying a user-defined weighting value or prioritizationfunction to prefer certain receivers above others.J. Comparators shall be equipped for DC battery float operation unless specified otherwise.Tower Top PreamplifiersTower-top preamplifiers/filters will not be used.Antenna SystemsAntennasThe selection and design of antennas, transmitter combiners, and receiver multicouplers will bethe responsibility of the contractor, but shall comply with the following specifications:A. Each antenna shall be equipped with a dedicated transmission line to the combiner ormulticoupler equipment.B. All antennas shall be mounted to minimize the pattern distortion effects caused by towermembers, transmission lines, other antennas, and other objects located near the antenna.C. Receive antennas shall be plumbed and mounted vertically above the transmit antennas asspace on the towers permits.D. Antennas shall meet or exceed the requirements of Part I of EIA-329-A. Separate transmitand receive antennas shall be provided unless otherwise specified.E. Multiple-feed antennas for transmitters (having separate elements inside one antenna radome)may be used to minimize tower loading and allow more space for other antennas.F. Antennas shall be high quality, ruggedized models, designed for long-term, high-reliabilityperformance under high wind conditions, and for minimal generation of passiveintermodulation.G. Repeater sites shall use Decibel Products DB-408, DB-420 or approved equivalent antennas.Transmission LinesA. Andrew LDF5-50A, 7/8 inch Heliax® cable shall be used for the major portions of the cableruns. Outdoor cable runs shall be continuous lengths, unless cable lengths exceed themaximum length supplied by the manufacturer. The manufacturers’ minimum bending radiusshall not be exceeded during installation.B. Andrew FSJ4-50B, 1/2 inch super-flex Heliax® cable shall be used in short lengths wheregreater flexibility is necessary. This includes each antenna and connection to all equipment.C. All cables shall be terminated in N-type connectors unless equipment requires otherwise.Connectors shall be constructed of non-ferrous materials, and shall have gold plated innerconductors and silver-plated bodies. Andrew Model LDF5-P, premium performance, Type Nmale and female connectors shall be used for all transmission line connections.City of San Luis Obispo 20 Radio System Upgrade TECHNICAL APPENDIX
D. Easiax cable cutting tool, Andrews Model 222951, shall be used to terminate all cables. Forreplacement blades, use Andrews Model 222954 blade kit (5 per kit).E. Antenna connectors shall be weatherproofed, using Andrew type 221213 weatherproofing kitor approved equivalent. Butyl-rubber tape shall be applied liberally to the antenna connectorand 3M Scotchcoat® shall be applied liberally over the butyl-rubber tape.F. Cable selection shall minimize transmission losses to less than 10% of total transmitterpower; this shall include connector losses.G. Transmission lines shall be secured through standard cable hangers attached to channelsupports or "Unistrut" as appropriate. All cables shall be dressed appropriately, and runparallel to each other.H. Antenna transmission lines shall be grounded just prior to entering the facility.I. When required, six-opening feed-through panels shall be provided at repeater sites, if theexisting is filled to capacity. Feed-throughs shall be similar to Andrew model 48940-6. Wallfeed-through boots shall be sized for the correct cable OD. Feed-through panels, boots andunused ports shall be sealed to prevent moisture and dust intrusion.J. Each transmission line shall be protected from lightning and static discharges with anappropriate Transient Voltage Surge Suppression (“TVSS”) device designed with a voltagehandlingcapability to support the number of transmitters anticipated, plus one future. TheTVSS device shall conform to all of the requirements shown elsewhere in this Specification.These devices shall be connected to the facility grounding system as described elsewhere inthis specification.K. TVSS units shall be mounted to contractor-provided copper cage assemblies that shall beinstalled at transmission line entry ports. This cage shall both ground and support TVSSunits. TVSS units shall be mounted in the cage in such a fashion as to permit easydisconnection of cables to/from external antennas for testing.Antenna Support StructuresDetails of antenna mounting shall be determined by the contractor, as required by the availabilityof support structures at each site and the contractor's specific design, and in coordination with theCity’s Project Manager.All contractor-provided hardware shall be the highest-quality stainless steel or galvanized.Antenna brackets shall be Andrews/Decibel Products models or engineer-approved equal.Cable Support StructuresThe City shall provide all indoor and outdoor cable support structures unless otherwise noted.This includes cable trays, ladders and “Unistrut” where application. However, contractor isrequired to provide cable support and standoff brackets, etc., as applicable, which will mount toCity-provided supports. All contractor-provided hardware shall be the highest- quality stainlesssteel or galvanized. Hardware shall be Andrews/Decibel Products models or engineer-approvedequal.Fire Station 1 Tower Antenna SystemA. The contractor shall supply and install all antennas, mounting brackets and hardware,transmission lines, connectors, TVSS devices and other hardware on the new FS#1City of San Luis Obispo 21 Radio System Upgrade TECHNICAL APPENDIX
Page 1 and 2: Technical AppendixSpecifications fo
Page 3 and 4: Technical Appendix to Specification
Page 5 and 6: Table 1 - Planned Primary City Radi
Page 7 and 8: To ensure both multi-source procure
Page 9 and 10: System Manager WorkstationA System
Page 11 and 12: Special Operational RequirementsAmo
Page 13 and 14: Table 5 - User Equipment and Access
Page 15 and 16: Control Station EquipmentSpare Cont
Page 17 and 18: C. Conventional repeaters site shal
Page 19: VHF Receiver SpecificationsFrequenc
Page 23 and 24: All cables will be dressed appropri
Page 25 and 26: Receiver MulticouplersA. The select
Page 27 and 28: Equipment HousingAll fixed-site rad
Page 29 and 30: Indoor coverage assumed using - 8dB
Page 31 and 32: Section 3. DISPATCH WORKSTATIONSIt
Page 33 and 34: 11. Operating system shall be capab
Page 35 and 36: transmission. All dispatchers and f
Page 37 and 38: center and surrounding area. Each p
Page 39 and 40: automatically assuming all function
Page 41 and 42: G. Provide two Ethernet ports at th
Page 43 and 44: Section 4.INTERCONNECT SYSTEMSThis
Page 45 and 46: A. SNMP (Simple Network Management
Page 47 and 48: 2. Frame failure (FRMF)3. PCM Failu
Page 49 and 50: B. Equipment MountingAll equipment
Page 51 and 52: H. Radios shall be capable of conve
Page 53 and 54: I. Channels: Radios and associated
Page 55 and 56: G. 48 Channels: Radios and the asso
Page 57 and 58: Vehicle AntennasA. All vehicular an
Page 59 and 60: I. Radios shall be housed in rugged
Page 61 and 62: K. Cases: D-clip type swivel mount
Page 63 and 64: Table 19B. - VHF Portable Radio Rec
Page 65 and 66: Section 7. CONTROL STATION EQUIPMEN
Page 67 and 68: control station, and/or multi-chann
Page 69 and 70: Table 22. - Dispatch Center Radio A
Page 71 and 72:
Section 8. BACKUP POWER SYSTEMSThis
Page 73 and 74:
B. Electrical Noise: Less than 100m
Page 75 and 76:
J. Providing electrical connections
Page 77 and 78:
I. Significant inter-cabling, wheth
Page 79 and 80:
D. Transmission lines shall be secu
Page 81 and 82:
Terminating Cross ConnectA. To cons
Page 83 and 84:
Section 10. MANAGEMENT AND TRAINING
Page 85 and 86:
Section 12. DELIVERY AND STORAGE OF
Page 87 and 88:
specifications, the contractor’s
Page 89 and 90:
H. The Operational System Test shal
Page 91 and 92:
Section 15. PREVENTIVE MAINTENANCEA
Page 93:
D. A detailed inventory of fixed eq
show all

Technical Appendix Specifications for the RADIO SYSTEM UPGRADE

Create successful ePaper yourself

Delete template?

Save as template?