UL Addendum - Tyco Security Products

More documents

Recommendations

Info

OPERATIONAL REQUIREMENTSOperation/Testing1. Readers are tested by reading a sample card and observing the results on the MonitoringStation application. If the reader and card formats are properly set, an “access granted” or“access denied” message appears on the screen. A “card misread” message indicates that thereader is not properly installed or the card format does not match the settings in the C•CURE800/8000 Administration application.2. Inputs are tested by opening/closing (activating/deactivating) the device. Input devices musthave the proper supervision resistors installed to function with C•CURE 800/8000. Wheninputs are working properly, you see the messages “input xxx activated” and “input xxxdeactivated. Shorting or opening the cable is indicated as “input xxx open loop” or “inputxxx shorted” on the Monitoring Station application.3. Outputs are tested by performing a manual action in the Monitoring Station application. Youcan momentary open a door or activate any other relay. You can then use a resistance meterto determine if the relay contacts close and open properly.Maintenance• For electronic modules exposed to high dust environments: Check the assemblies forexcess dust build-up every 6 months and remove the dust and dirt from the assemblies withforced air.• For readers exposed to external weather conditions: Check the enclosure sealing for leaksat 6-month intervals. If the seal is not intact, replace the gasket.12 C·CURE 800/8000 V9.4 UL Addendum
OPERATIONAL RESTRICTIONSThe following conditions are not recommended, and may result in impaired operation of thesystem component.Proximity Card Readers• All Software House RM reader series products can be installed on metal surfaces. Somethird-party readers, such as HID ProxPro Plus, may exhibit reduced performance whenmounted near a metal object. Consult the installation guide or users’ manual for each specificproduct.• Performance may also degrade if the reader is exposed to any Radio Frequency fields withfrequencies near 125 KHz or 13.56 MHz.• The cable used to connect a Wiegand reader must not exceed 500 ft.Magnetic Stripe Readers• Performance may degrade or the unit stops working if installed near magnetic sources, suchas a motor.• The cable used to connect a magnetic read head must not exceed 10 ft.Note: In general, do not run reader cabling near high voltage lines or motorized equipment, suchas elevators or compressors.SUPPORTED/UNSUPPORTED FEATURESIN C•CURE 800/8000 VERSION 9.3Table 8 shows the features that were evaluated by UL.Table 8. Features Evaluated by ULFeatureEvent/Alarm MonitoringDoor ControlElevator ControlTime SpecificationsTime Zone ManagementOperator PrivilegesUL TestedYesYesYesYesYesYesC·CURE 800/8000 V9.4 UL Addendum13
Page 1 and 2: C•CURE 800/8000 System and Compon
Page 3 and 4: OVERVIEWThis addendum provides UL r
Page 5 and 6: SOFTWARE CONFIGURATION REQUIREMENTS
Page 7 and 8: MINIMUM PC CONFIGURATION FOR C•CU
Page 9 and 10: Table 4. Server Requirements - Five
Page 11 and 12: INSTALLATION LOCATIONSThe following
Page 13: ModelOperatingTemperature(Environme
Page 17 and 18: FeatureCarpool Anti-passbackArea Mu
Page 19 and 20: RepliStor replicates data from one
Page 21 and 22: Product Code Description Field Repl
Page 23 and 24: Product Code Description Field Repl
Page 25 and 26: Outputs Open collector, +12V DC, 0.
Page 27 and 28: Wiring Readers To an iSTARC·CURE 8
Page 29 and 30: The following diagram show typical
Page 31 and 32: Single Device Alarm Zone:Normally O
Page 33 and 34: Single Resistor End Line ModeWiring
Page 35 and 36: iSTAR Backup DatabaseThe software s
Page 37 and 38: Dual End-Of-Line (NC) Configuration
Page 39 and 40: UL LISTED ENCRYPTED LINE SECURITY C
Page 41 and 42: Network ConfigurationThe "UL Listed
Page 43 and 44: PNET1 InstallationPNET1 PhotographC
Page 45: APC Safety• Catastrophic Event Pr

UL Addendum - Tyco Security Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?