UL Addendum - Tyco Security Products

More documents

Recommendations

Info

3 RD PARTY LEGACY INPUT SUPERVISION SUPPORTC•CURE 800 version 9.3 and iSTAR eX firmware 4.3.provide support for MDI type SupervisedInput Configurations. This option allows C•CURE systems to reuse previously wired legacyinputs.Definitions, Acronyms, and AbbreviationsNormally Open Input – an input with a contact closure switch that is in the open position whenin the Secure state, and in the closed position in the Alarm state.Normally Closed Input – an input with a contact closure switch that is in the closed positionwhen in the Secure state, and in the open position in the Alarm state.Supervising Resistor – a resistor in the circuit of an input that provides known expected valueswhen in the Secure and Alarm states.Single End-Of-Line input – a supervised input that uses a single supervising resistor either inseries or parallel with the contact closure switch.Dual End-Of-Line input – a supervised input that uses two supervising resistors, typically withone resistor in parallel with the sense switch, and the other resistor in series with the first resistorand switch. Alternatively, one resistor may be series with the switch only, and resistor in parallelwith series resistor and switch.NO – Normally OpenNC – Normally ClosedEOL – End-Of-LineSupport for MDI Type Supervised Input ConfigurationsThe Software House iSTAR controllers are able to support legacy supervised inputconfigurations using 1K and 2K resistors, similar to those used by MDI.The iSTAR controllers can be retrofitted to installations with supervised inputs which had beenpreviously wired for legacy systems.The two types of inputs which are supported are 1K ohm Single End-Of-Line (Single EOL)configurations, and 1K / 2K ohm Double End-Of-Line (Double EOL) configurations.The 1K Single inputs can be wired to any input on an iSTAR Pro or eX.The 1K / 2K Double inputs must be connected to an I/8 board, which is connected to an RM buson any iSTAR.34 C·CURE 800/8000 V9.4 UL Addendum
Dual End-Of-Line (NC) ConfigurationsMDI Dual End-Of-Line configurations are wired for Normally Closed (NC) switches, as shownin the diagram below:The above configuration is similar to the Normally Closed case of the Software House standardsupervision configuration, with the following exceptions:• The Alarm state presents a 3K ohm resistance (instead of 2K ohm for Software Housestandard configuration)• The C•CURE 800 system does not recognize the legacy 3 rd party 4K ohm Tamper state.C·CURE 800/8000 V9.4 UL Addendum35
Page 1 and 2: C•CURE 800/8000 System and Compon
Page 3 and 4: OVERVIEWThis addendum provides UL r
Page 5 and 6: SOFTWARE CONFIGURATION REQUIREMENTS
Page 7 and 8: MINIMUM PC CONFIGURATION FOR C•CU
Page 9 and 10: Table 4. Server Requirements - Five
Page 11 and 12: INSTALLATION LOCATIONSThe following
Page 13 and 14: ModelOperatingTemperature(Environme
Page 15 and 16: OPERATIONAL RESTRICTIONSThe followi
Page 17 and 18: FeatureCarpool Anti-passbackArea Mu
Page 19 and 20: RepliStor replicates data from one
Page 21 and 22: Product Code Description Field Repl
Page 23 and 24: Product Code Description Field Repl
Page 25 and 26: Outputs Open collector, +12V DC, 0.
Page 27 and 28: Wiring Readers To an iSTARC·CURE 8
Page 29 and 30: The following diagram show typical
Page 31 and 32: Single Device Alarm Zone:Normally O
Page 33 and 34: Single Resistor End Line ModeWiring
Page 35: iSTAR Backup DatabaseThe software s
Page 39 and 40: UL LISTED ENCRYPTED LINE SECURITY C
Page 41 and 42: Network ConfigurationThe "UL Listed
Page 43 and 44: PNET1 InstallationPNET1 PhotographC
Page 45: APC Safety• Catastrophic Event Pr

UL Addendum - Tyco Security Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?