UL Addendum - Tyco Security Products

More documents

Recommendations

Info

apC/L Access Control PanelInput powerSignal InputsOutputs18 VAC, 50 VAClass A Supervised, 0 - 14,000 ohmsDry contacts rated at 30 V AC/DC, 1.0 A non-inductiveiSTAR Access Control PanelInput power 100 – 240 VAC, 2.3A @100 VAC, 1.1A @240 VAC, 47-63HzSignal InputsOutputsClass A Supervised, 0 - 14,000 ohmsDry contacts rated at 30 V AC/DC, 5.0 A non-inductiveReaders: RM1-MP, RM2-MPInput powerSignal Inputs+12V DC, +/-5%, 80mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM2L-MPInput powerSignal Inputs+12V DC, +/-5%, 180mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM3-MPInput powerSignal Inputs+12V DC, +/-5%, 80mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM1-PI, RM2-PIInput powerSignal Inputs+12V DC, +/-5%, 80mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM2L-PIInput powerSignal Inputs+12V DC, +/-5%, 180mAClass A Supervised, 0 - 14,000 ohms22 C·CURE 800/8000 V9.4 UL Addendum
Outputs Open collector, +12V DC, 0.5AReaders: RM1-PH, RM2-PHInput powerSignal Inputs+12V DC, +/-5%, 250mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM2L-PHInput powerSignal Inputs+12V DC, +/-5%, 250mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM3-PHInput powerSignal Inputs+12V DC, +/-5%, 250mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5AReaders: RM1-WInput powerSignal Inputs+12V DC, +/-5%, 80mAClass A Supervised, 0 - 14,000 ohmsOutputs Open collector, +12V DC, 0.5ACabling and WireNote: All external connections (relays, battery wires, power supply wires, readers, etc.) must bemade to power limited circuits only. All cabling and wire used must be UL Listed and/orRecognized wire and must be suitable for the application, as described below.Wiring Main Power To an iSTARThe iSTAR must be connected to a power limited main circuit. Cabling must be UL Listedand/or Recognized. Refer to the product label for power requirements. The connection procedureis shown in the following diagram.1. Attach the conduit for the wiring from AC main power to the knockout closest to the powersupply in the enclosure.C·CURE 800/8000 V9.4 UL Addendum23
Page 1 and 2: C•CURE 800/8000 System and Compon
Page 3 and 4: OVERVIEWThis addendum provides UL r
Page 5 and 6: SOFTWARE CONFIGURATION REQUIREMENTS
Page 7 and 8: MINIMUM PC CONFIGURATION FOR C•CU
Page 9 and 10: Table 4. Server Requirements - Five
Page 11 and 12: INSTALLATION LOCATIONSThe following
Page 13 and 14: ModelOperatingTemperature(Environme
Page 15 and 16: OPERATIONAL RESTRICTIONSThe followi
Page 17 and 18: FeatureCarpool Anti-passbackArea Mu
Page 19 and 20: RepliStor replicates data from one
Page 21 and 22: Product Code Description Field Repl
Page 23: Product Code Description Field Repl
Page 27 and 28: Wiring Readers To an iSTARC·CURE 8
Page 29 and 30: The following diagram show typical
Page 31 and 32: Single Device Alarm Zone:Normally O
Page 33 and 34: Single Resistor End Line ModeWiring
Page 35 and 36: iSTAR Backup DatabaseThe software s
Page 37 and 38: Dual End-Of-Line (NC) Configuration
Page 39 and 40: UL LISTED ENCRYPTED LINE SECURITY C
Page 41 and 42: Network ConfigurationThe "UL Listed
Page 43 and 44: PNET1 InstallationPNET1 PhotographC
Page 45: APC Safety• Catastrophic Event Pr

UL Addendum - Tyco Security Products

Create successful ePaper yourself

Delete template?

Save as template?