UL Addendum - Tyco Security Products

More documents

Recommendations

Info

Secondary Protectors for Data Communication Circuits, UL 497A. These protectors shall beused only on the protected side of the telecommunications network. This includes the TCP/IPnetwork and serial data lines for all C•CURE 800/8000 equipment such as client and servercomputers network ports and server serial ports. Excluded from this requirement are the datalines that feed directly in to apC/L and apC/8X panels and iSTAR controllers.Temperature Controlled EnvironmentThe C•CURE 800/8000 server computer must be installed in a temperature-controlledenvironment that is maintained by the HVAC system to be in the range of 13-35°C (55-95°F).The HVAC system must be provided with at least 24 hours of standby power supplied by anengine-driven generator or standby battery. Excluded from this requirement are apC/L andapC/8X panels and iSTAR controllers and their periphery equipment like RMs and I/8 boards.Backup SystemThe C•CURE 800/8000 server computer must be completely duplicated with provision forswitchover to the backup system within 30 seconds. The backup system may be provided by asecond computer that meets C•CURE 800/8000 UL 1076 Listing requirements or by using afault tolerant computer. If a fault tolerant computer is used, every component, including thesoftware and the power supply, must be duplicated.Uninterruptible Power Supply (UPS)In addition to the standby power required for the HVAC system, all system components must beprovided with UPS with sufficient capacity to operate the equipment for a minimum of 15minutes. If more than 15 minutes is required for HVAC standby power to come on-line andstabilize, the UPS must be capable of providing input for at least that amount of time. When theUPS is installed, there must be a means for disconnecting the input to the UPS while maintainingcontinuity of power to the system components so that maintenance and repair can be performed.All UPS devices must comply with the Standard for Uninterruptible Power Supply Equipment,UL 1778, or the Standard for Fire Protective Signaling Devices, UL 1481.2 C·CURE 800/8000 V9.4 UL Addendum
SOFTWARE CONFIGURATION REQUIREMENTSMonitoring Station PollingThe Monitoring Station polls the server to ensure that the server and communications circuit isoperational. The polling frequency is user-configurable and can be changed through DiagSystemby modifying the Monitoring Station system variable, “NetworkPollingInterval.” The intervalbetween polls must not exceed 90seconds.Dial-up Communication Circuit ConfigurationThe C•CURE 800/8000 supports the configuration of dial-up communication circuits betweenthe server and apCs.Note: This configuration must not be used in a UL 1076 system.Cabinet Tamper Detection InputsThe C•CURE 800/8000 supports inputs that detect cabinet tamper for apCs, iSTARs, and RMs.All apCs, iSTARs, and RMs must be configured to detect cabinet tamper. Each tamper inputmust specify that an event be triggered when the device is tampered. This event must beconfigured to always be armed, on-line, annunciated, and require acknowledgement.AC Power Fail Inputs for apCs and iSTARsThe C•CURE 800/8000 supports inputs that detect AC power fail for apCs and iSTARs. AllapCs and iSTARs must be configured to detect AC power fail. Each AC power fail input mustspecify that an event be triggered when the apC or iSTAR loses AC power. This event must beconfigured to always be armed, on-line, annunciated, and require acknowledgement.Event Association with apC, iSTAR, and RM Communications FailureThe C•CURE 800/8000 supports the association of events with apC, iSTAR, and RMcommunications failure. Each apC, iSTAR, and RM must be configured to trigger an event whenthe device goes into communications failure. This event must be configured to always be armed,on-line, annunciated, and require acknowledgement.Supervised Inputs on apCs, iSTARs and I/8 - I/32 BoardsThe C•CURE 800/8000 supports supervised inputs located on apCs, iSTARs, and I8/I32 boards.Each supervised input must be configured to trigger an event when the input is activated and asupervision error is detected for the input. These events must be configured to always be armed,on-line, annunciated, and require acknowledgement.C·CURE 800/8000 V9.4 UL Addendum3
Page 1 and 2: C•CURE 800/8000 System and Compon
Page 3: OVERVIEWThis addendum provides UL r
Page 7 and 8: MINIMUM PC CONFIGURATION FOR C•CU
Page 9 and 10: Table 4. Server Requirements - Five
Page 11 and 12: INSTALLATION LOCATIONSThe following
Page 13 and 14: ModelOperatingTemperature(Environme
Page 15 and 16: OPERATIONAL RESTRICTIONSThe followi
Page 17 and 18: FeatureCarpool Anti-passbackArea Mu
Page 19 and 20: RepliStor replicates data from one
Page 21 and 22: Product Code Description Field Repl
Page 23 and 24: Product Code Description Field Repl
Page 25 and 26: Outputs Open collector, +12V DC, 0.
Page 27 and 28: Wiring Readers To an iSTARC·CURE 8
Page 29 and 30: The following diagram show typical
Page 31 and 32: Single Device Alarm Zone:Normally O
Page 33 and 34: Single Resistor End Line ModeWiring
Page 35 and 36: iSTAR Backup DatabaseThe software s
Page 37 and 38: Dual End-Of-Line (NC) Configuration
Page 39 and 40: UL LISTED ENCRYPTED LINE SECURITY C
Page 41 and 42: Network ConfigurationThe "UL Listed
Page 43 and 44: PNET1 InstallationPNET1 PhotographC
Page 45: APC Safety• Catastrophic Event Pr

UL Addendum - Tyco Security Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?