1066 Liquid Analytical Transmitter - Emerson Process Management

More documents

Recommendations

Info

Section 10: HART CommunicationSeptember 20131066 Instruction ManualLIQ_MAN_10661066DO Device VariablesDevice Variable Name Assignable to Dynamic Variables Variable RangePrimary Value Type:Oxygen (17) PV, SV, TV or QV 0 to 100 ppm0 to 1000 ppb0 to 100 mg/L0 to 1000 µg/L0 to 300 % Saturation0 to 760 mmHg0 to 30 inHg0 to 1 bar0 to 1000 mbar0 to 100 kPa0 to 1 atmOther Device Variables:Temperature PV, SV, TV or QV -15 to 200 °C5 to 360 °FTemperature resistance TV or QV 0 to 100000Sensor input current PV, SV, TV or QV 0 to 100000 nA1066OZ Device VariablesDevice Variable Name Assignable to Dynamic Variables Variable RangePrimary Value Type:Ozone (18) PV, SV, TV or QV 0 to 20 ppm0 to 1000 ppb0 to 20 mg/L0 to 1000 µg/LOther Device Variables:Temperature PV, SV, TV or QV -15 to 200 °C5 to 360 °FTemperature resistance TV or QV 0 to 100000Sensor input current PV, SV, TV or QV 0 to 100000 nA1066CL Device VariablesDevice Variable Name Assignable to Dynamic Variables Variable RangePrimary Value Type:Chlorine (19) PV, SV, TV or QV 0 to 20 ppm0 to 1000 ppb0 to 20 mg/L0 to 1000 µg/LOther Device Variables:Temperature PV, SV, TV or QV -15 to 200 °C5 to 360 °FTemperature resistance TV or QV 0 to 100000Sensor input current PV, SV, TV or QV 0 to 100000 nApH (free chlorine pH compensation) SV, TV or QV 0 to 14 pH106 HART Communications
1066 Instruction Manual Section 10: HART CommunicationLIQ_MAN_1066 September 2013APPENDIX 10.2 – Additional Transmitter Status –Command 48 Status Bits1066 pH Device VariablesByte / Bit Meaning / Class Device Status Bits Set1 / 0CPU Error / ErrorThe software checksum is not as expected. The CPU memory has been corrupted.4 – More Status Available7 – Field Device Malfunction1 / 1Self-Test Fail / ErrorAn electronic component is out of specification.4 – More Status Available7 – Field Device Malfunction1 / 2Factory Data Error / ErrorAn error was detected in the factory segment of the non-volatile memory. Atleast one factory configuration parameter has been corrupted.4 – More Status Available7 – Field Device Malfunction1 / 31 / 43 / 03 / 13 / 23 / 33 / 7Hardware/Software Mismatch / ErrorThe software is not compatible with the hardware.Internal Communications Error / ErrorThe analog input electronics is non-responsive.Keypad Error / WarningAt least one key in the device keypad is stuck. This condition makes the localoperator interface unuseable. If no other alerts are present, the device canstill perform its other functions normally.User Data Error / WarningAn error was detected in the non-volatile memory. One or more user configurationparameter may be corrupted. Reset analyzer to factory defaults andre-configure the device. If the problem persists, replace device.Need Factory Calibration / WarningThe device's non-volatile memory has been corrupted. The device measurementsmay be out of specification.Software Mismatch / WarningThe input CPU software is not fully compatible with the main CPU software.Reset In Progress / OtherThe transmitter's configuration is being reset to factory defaults.4 – More Status Available7 – Field Device Malfunction4 – More Status Available7 – Field Device Malfunction4 – More Status Available4 – More Status Available4 – More Status Available4 – More Status Available4 – More Status Available6 / 6 Maintenance Required / Other 4 – More Status Available6 / 1 Device Variable Alert / Other 4 – More Status Available8 / 0Simulation Active / ModeA device variable is being simulated.4 – More Status Available8 / 1 Non-Volatile Memory Defect / Warning 4 – More Status Available8 / 2 Volatile Memory Defect / Error 4 – More Status Available8 / 3 Watchdog Reset Executed / Other 4 – More Status Available8 / 4 Power Supply Condition Out Of Range / Warning 4 – More Status Available8 / 5 Environmental Condition Out Of Range / Warning 4 – More Status Available8 / 6Electronic Defect / ErrorReset device or turn power off then on. If problem persists, replace device.4 – More Status AvailableHART Communications 107
Page 1 and 2:
1066 Liquid AnalyticalTransmitter10
Page 3:
Essential InstructionsRead this pag
Page 7 and 8:
1066 Instruction Manual Table of Co
Page 9 and 10:
1066 Instruction Manual Table of Co
Page 11 and 12:
1066 Instruction Manual Section 1:
Page 13 and 14:
Page 15 and 16:
Page 18 and 19:
Section 2: Description and specific
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Section 3: InstallationSeptember 20
Page 26 and 27:
Section 3: InstallationSeptember 20
Page 28 and 29:
Section 4: WiringSeptember 20131066
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Section 5: Intrinsically Safe Insta
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Section 6: Display and OperationSep
Page 50 and 51:
Section 6: Display and OperationSep
Page 52 and 53:
Section 7: Transmitter ProgrammingS
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Section 8: Programming Measurements
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67: Section 8: Programming Measurements
Page 82 and 83: Section 9: CalibrationSeptember 201
Page 100 and 101: MAINMENUCarate1.234µS/cm 25.0ºCCa
Page 108 and 109: Section 10: HART CommunicationSepte
Page 136 and 137: EC Declaration of ConformitySeptemb
Page 138 and 139: EC Declaration of ConformitySeptemb
Page 140: LIQ_MAN_1066Rev. FSeptember 2013fac
show all

1066 Liquid Analytical Transmitter - Emerson Process Management

Create successful ePaper yourself

Delete template?

Save as template?