1066 Liquid Analytical Transmitter - Emerson Process Management

More documents

Recommendations

Info

Section 2: Description and specificationsSeptember 20131066 Instruction ManualLIQ_MAN_1066This page left intentionally blank12 Specifications
1066 Instruction Manual Section 3: InstallationLIQ_MAN_1066 September 2013Section 3: Installation3.1Unpacking and inspectionInspect the shipping container. If it is damaged, contact the shipper immediately for instructions.Save the box. If there is no apparent damage, unpack the container. Be sure all items shown on thepacking list are present. If items are missing, notify Rosemount Analytical immediately.3.23.3Installation – general information1. Although the transmitter is suitable for outdoor use, installation is direct sunlight or in areasof extreme temperatures is not recommended unless a sunshield is used.2. Install the transmitter in an area where vibration and electromagnetic and radio frequencyinterference are minimized or absent.3. Keep the transmitter and sensor wiring at least one foot from high voltage conductors. Be surethere is easy access to the transmitter.4. The transmitter is suitable for panel, pipe, or surface mounting.5. The transmitter case has six 1/2-inch (PG13.5) conduit openings. Use separate conduit openingsfor the power/output cable, the sensor cable, and the other the sensor cable as needed(pH input for free chlorine with continuous pH correction).6. Use weathertight cable glands to keep moisture out to the transmitter. If conduit is used, plugand seal the connections at the transmitter housing to prevent moisture from getting insidethe instrument.Preparing conduit openingsThere are six conduit openings in all configurations of 1066.Conduit openings accept 1/2-inch conduit fittings or PG13.5 cable glands. To keep the case watertight,block unused openings with NEMA 4X or IP66 conduit plugs.To maintain ingress protection for outdoor use, seal unused conduit holes with suitable conduitplugs.NOTE: Use watertight fittings and hubs that comply with your requirements. Connect the conduithub to the conduit before attaching the fitting to the transmitter.Electrical installation must be in accordance with the National Electrical Code (ANSI/NFPA-70) and/orany other applicable national or local codes.Installation 13
Page 1 and 2: 1066 Liquid AnalyticalTransmitter10
Page 3: Essential InstructionsRead this pag
Page 7 and 8: 1066 Instruction Manual Table of Co
Page 9 and 10: 1066 Instruction Manual Table of Co
Page 11 and 12: 1066 Instruction Manual Section 1:
Page 18 and 19: Section 2: Description and specific
Page 20 and 21: Section 2: Description and specific
Page 24 and 25: Section 3: InstallationSeptember 20
Page 26 and 27: Section 3: InstallationSeptember 20
Page 28 and 29: Section 4: WiringSeptember 20131066
Page 40 and 41: Section 5: Intrinsically Safe Insta
Page 48 and 49: Section 6: Display and OperationSep
Page 50 and 51: Section 6: Display and OperationSep
Page 52 and 53: Section 7: Transmitter ProgrammingS
Page 58 and 59: Section 8: Programming Measurements
Page 72 and 73:
Section 8: Programming Measurements
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Section 9: CalibrationSeptember 201
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
MAINMENUCarate1.234µS/cm 25.0ºCCa
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Section 10: HART CommunicationSepte
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
EC Declaration of ConformitySeptemb
Page 138 and 139:
EC Declaration of ConformitySeptemb
Page 140:
LIQ_MAN_1066Rev. FSeptember 2013fac
show all

1066 Liquid Analytical Transmitter - Emerson Process Management

Create successful ePaper yourself

Delete template?

Save as template?