SPECIFICATIONS

More documents

Recommendations

Info

Fort Nelson NRRM TESTING, ADJUSTING & SECTION 15990 Airport Terminal Building BALANCING Page: 2 Washroom Renovations • Fan total air volume at 100% return air, “minimum” outdoor air, and 100% outdoor air settings. • Fan speed. • Fan motor current, and rated motor current. • Entering and leaving air temperatures for each heating coil. 3. Water Systems (HVAC): Water circulating systems shall be balanced by means of balancing fittings and tabulated results shall include the following: • Differential head across all circulating pumps. • Flow and return water temperature to supply and return header for all zones. • Water temperature supplied to and returning from each coil and heating element. 4. Contractor shall arrange with balancing technician to have water flow through radiation elements checked prior to installation of radiation enclosure. 5. Domestic Hot Water Recirculation System: Domestic hot water recirculation system shall be balanced by proportioning the water flow at balancing fittings and ensuring adequate flow through each circuit. 6. Testing of Fire Dampers & Fire Stop Flaps: The Balancing/Testing Agency shall conduct a "trip" test on all fire dampers and fire stop flaps to ensure that fire mechanisms function correctly and that dampers attain a fully closed position when tripped. A copy of test results tabulating the fire damper location, size, and date of trip test, shall be sent to the Engineer for record purposes. Copies shall also be inserted in Equipment Maintenance Manuals. Dampers and Flaps which fail to function correctly shall be re-tested after corrective action has been completed. Any fusible links damaged when conducting tests shall be replaced by this Contractor. A signed and dated test label shall be attached to each fire damper upon completion of test and resetting of fire damper. 7. CAD drawing files of the heating and ventilating tender drawings will be made available to the Balancing Contractor if requested. To cover administrative time and the cost of retrieval and transmission of files, a charge of $25.00 will be made for each drawing requested, to an upset maximum of $150 per project. An "Authorization to use CAD Drawing File" agreement restricting the use of the CAD files to the preparation of the project balancing reports must be signed prior to obtaining the files. February 2012 JM BEAN & CO. LTD 1130.10
Fort Nelson NRRM TESTING, ADJUSTING & SECTION 15990 Airport Terminal Building BALANCING Page: 3 Washroom Renovations 15996 OPERATING INSTRUCTIONS 1. During "substantial performance" review of the work the Mechanical Contractor, together with the Engineer, Control Sub-contractor, and other Sub-contractors designated by the Engineer, shall instruct the Owner's operating personnel in the proper operation and maintenance of all systems and equipment installed under the contract. 2. It shall be the Mechanical Contractor's responsibility to have the specified equipment manuals prepared, previously approved by the Engineer, and ready for presentation to the Owner at this meeting. 3. Convene the meeting with the aforementioned parties at the time called for in the substantial performance review. The arrangements shall include written notices to all the parties concerned. Should the equipment manuals, or system installation not be complete and operable at the proper time, he shall then convene the operating instruction meeting at a later date and pay any additional costs including time and travelling expenses for the personnel involved which are attributable to the delay. 15997 EQUIPMENT MANUALS 1. Provide three hard covered, durable plastic bound, loose leaf equipment manuals with index page and tabs. 2. Equipment manuals shall contain the system description, manufacturer's descriptive literature, installation instructions and maintenance recommendations relative to methods and frequency requirements for lubrication, filter cleaning, belt adjustment and other items. Specific recommendations of the manufacturer relative to lubricants, adhesives, etc. will be required. Where literature furnished covers several models of the equipment, all data except that pertaining to the model installed shall be neatly "ruled" out. 3. For each fan and pump installed, provide performance data in "Curve" or multi rating table. 4. For each plumbing fixture, floor and roof drain installed, provide manufacturer's "cut" of that item and "cuts" of associated brass goods. 5. Copies of extended guarantees and warranties for equipment items such as hot water tanks and heat exchangers shall be included in a separate section of the manual. 6. A draft copy of the system description shall be sent to the Engineer for review and a final copy sent for record files. 7. These manuals shall be compiled by Balancing Contractor as outlined in Scope Clause. The Mechanical Contractor shall furnish sufficient copies of equipment manufacturer's literature to the Balancing Contractor to meet the above requirements. END of SECTION 15990 February 2012 JM BEAN & CO. LTD 1130.10
Page 1 and 2:
SPECIFICATIONS
Page 3:
ROOF FRAMING PLAN 1:50
Page 14 and 15:
File No.: FN321 Page i TABLE OF CON
Page 16 and 17:
File No.: FN321 Page 1 1.0 INTRODUC
Page 18 and 19:
File No.: FN321 Page 3 Where: h =
Page 20 and 21:
File No.: FN321 Page 5 TABLE 3.1: U
Page 22 and 23:
File No.: FN321 Page 7 encountered.
Page 24 and 25:
File No.: FN321 Page 9 The soil pro
Page 26 and 27:
File No.: FN321 Page 11 TABLE 4.1:
Page 28 and 29:
File No.: FN321 Page 13 To enhance
Page 30 and 31:
File No.: FN321 Page 15 of the Fort
Page 32 and 33:
Appendix A
Page 34 and 35:
J.R. Paine &Associates Ltd. FILE NO
Page 36 and 37:
J.R. Paine &Associates Ltd. 2 The d
Page 38 and 39:
I - ~ J.R. Paine &Associates Ltd. 4
Page 40 and 41:
[ J.R. Paine &Associates Ltd. 6 APP
Page 42 and 43:
~ PROJECT: Ft. NelsonAirportLight S
Page 44 and 45:
~ I PROJECT: Ft. NelsonAirportLight
Page 46:
I @ SCREEN ANALYSIS Sample: Locatio
Page 49 and 50:
Fort Nelson NRRM TABLE OF CONTENTS
Page 51 and 52: Fort Nelson NRRM TABLE OF CONTENTS
Page 53 and 54: Fort Nelson NRRM BASIC MECHANICAL S
Page 73 and 74: Fort Nelson NRRM NOISE VIBRATION AN
Page 79 and 80: Fort Nelson NRRM MECHANICAL SECTION
Page 81 and 82: Fort Nelson NRRM MECHANICAL SECTION
Page 83 and 84: Fort Nelson NRRM PLUMBING SECTION 1
Page 89 and 90: Fort Nelson NRRM REFRIGERATION SECT
Page 91 and 92: Fort Nelson NRRM HEAT SECTION 15750
Page 93 and 94: Fort Nelson NRRM AIR HANDLING SECTI
Page 95 and 96: Fort Nelson NRRM AIR SECTION 15880
Page 97 and 98: Fort Nelson NRRM CONTROLS SECTION 1
Page 99 and 100: Fort Nelson NRRM CONTROLS SECTION 1
Page 101: Fort Nelson NRRM TESTING, ADJUSTING
Page 105 and 106: Fort Nelson NRRM Airport Terminal B
Page 107 and 108: Fort Nelson NRRM Airport Terminal B
show all

SPECIFICATIONS

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?