7 months ago



TRACK BIFOLD INSIDE MOUNT cont. OPUS INSIDE MOUNT ENCORE INSIDE MOUNT Attach L Bracket to underside of headboard Slide fascia between headboard and recess 20. Cover screw holes with screwcap stickers and gap fill if necessary to finish off. 21. Operate all louvre tilts and operate panels several times to make sure all components are working correctly. 22. Clean shutters and work space. OUTSIDE MOUNT: 1. Lay all of the framing pieces (boards) face up on the floor or your workspace. 2. Screw from above the headboard down into the sideboards. 3. Screw from sideboards into the bottom board if applicable, cover with screw caps. 4. Lift the assembled box unit and place against the wall in your measured position. 5. Tack into place with fixing screws taking care not to screw all the way into place. 6. Using a ladder: Fix the mounting block to the top of the headboard at the rear edge. For ENCORE aluminium shutters, use the 40x40 angle supplied as a mounting piece (diagrams below). 7. Screw through the mounting block or 40x40 angle into the wall, anchoring well: OPUS OUTSIDE MOUNT 40mm x 27mm Mounting block ENCORE OUTSIDE MOUNT 40mm x 40mm aluminium angle 54

TRACK BIFOLD OUTSIDE MOUNT cont. 8. For OPUS, attach the metal headboard support bracket to the rear of the mounting block. 9. Make necessary adjustments to ensure box out frame is level. 10. Drive headboard fixing screws in all the way. 11. Mount the light block lengths supplied to the rear inside edge of the sideboards (or use angle brackets instead of light block if preferred). 12. Screw through the light block into the wall or architrave to attach the sideboards. 13. Fit the bottom pivot plate. Measure from the front of the headboard to the centre of the top track and position the bottom pivot the same distance in, using sideboard as reference point in the absence of bottom board. 23. If no bottom board supplied, attach bottom tracks by measuring the distance from the edge of headboard to centre of each track and position the bottom tracks the same distance. Use the supplied double-sided tape to fix tracks in place direct to the floor. Ensure the track fits between pivot(s). (Does not apply to bottom board as track is recessed). 14. Check all necessary hardware/componentry is fitted into the top track and panels. 15. Fit panels working from the pivot side toward the centre of the opening. Locate the first pair with the pivot panel and attach this into the bottom pivot bracket. 16. The top pivot will already be attached to the panel, so spring load this into the top pivot bracket located in the top track. 17. The next panel will have a wheel carrier bracket. Attach this to the wheel carrier in the top and lock it in place. Compress the bottom guide and release into place in the bottom track. 18. If you have more than two panels stacking in one direction, sit the next pair beside the first, line the hinges up and insert hinge pins to attach then attach wheel carriers as above. 19. Repeat as required. 20. Make any necessary adjustments at the wheel carriers and pivot bracket to ensure panels are squared up and they operate correctly. 21. Attach returns to fascia if applicable using L brackets. 22. Attach L brackets to front edge of headboard according the diagrams below. 23. Position fascia 50mm above headboard then screw into bracket at rear of fascia. OPUS OUTSIDE MOUNT ENCORE OUTSIDE MOUNT Attach L Bracket to top face of headboard & screw into fascia Attach L Bracket to top face of headboard & screw into fascia 50mm 50mm 55

WorkEngine v3.x Installation Guide - EPM Live
Capitol Capitol - Minnesota's Private Colleges
Technical Guide -
Waspmote: Technical Guide - Libelium
Technical Guide - Hyster Company
Technical Guide - Hyster Company
Racor Products Technical Guide
Capitol Celebrates 80 Years! - Capitol College
Technical DATA Sheet and Guide -
LO5.0T Technical Guide - Hyster Company
Brochure / Technical Guide - Hyster Company
Technical Guide - Antietam Velo Club
HyPURITY HPLC Technical Guide - Chromatopak
Technical & Parts Guide - Wilwood Engineering
Brochure / Technical Guide - Hyster Company
Brochure / Technical Guide - Hyster Company
Capitol 02 - Consideratii generale