magicolor 3730DN User's Guide - Konica Minolta

Recommendations

Info

ENGINE With this menu, settings related to printer engine functions (such as ENERGY SAVER and ENGINE SUPPLIES REPLACE) can be specified. MENU ENGINE ENERGY SAVER AUTO CONTINUE ENGINE SERVICE TOTAL FACE COUNT COLOR FACE COUNT BW FACE COUNT BOOT VER. FPGA VER. CONTROLLER VER. ENGINE VER. COLOR CALIBRATION ENGINE SUPPLIES REPLACE RESTORE USER DEFAULT SUPPLIES REPLACE TRANS. BELT SUPPLIES REPLACE TRANS. ROLLER SUPPLIES REPLACE FUSER UNIT ENGINE 3-9
3-10 �� All factory default values are shown in bold. ENERGY SAVER AUTO CONTINUE ENGINE SERVICE Settings 120 minutes/60 minutes/30 minutes/ 15minutes Specify the length of time until the machine enters Energy Saver mode. �� The machine does not enter Energy Saver mode if paper has been loaded into Tray 1. Settings ON/OFF Select whether or not printing continues if the size or type of media in the selected tray is different from the size or type of media for the print job. If AUTO CONTINUE is set to ON, printing automatically continues if any of the following occur. Printing will be performed even if the media size is different. Different media size/type: SIZE MISMATCH (page 7-36)/ TYPE MISMATCH (page 7-37)/PUT MEDIA: TRAY X (page 7-40) TOTAL FACE COUNT COLOR FACE COUNT Displays the total page side counter. Displays the total page side counter for color printing. BW FACE COUNT Displays the total page side counter in black-and-white printing. BOOT VER. Displays the boot version. FPGA VER. Displays the FPGA version. CONTROLLER Displays the controller version. VER. ENGINE VER. Displays the engine version. COLOR CALIBRATION Settings YES/NO If YES is selected, color calibration is performed. ENGINE
Page 1 and 2: magicolor 3730DN User’s Guide A0V
Page 3 and 4: x-2 SOFTWARE LICENSE AGREEMENT This
Page 5 and 6: Contents 1 Introduction ...........
Page 7 and 8: x-6 Glossy Media ..................
Page 9 and 10: x-8 Contents
Page 11 and 12: Getting Acquainted with Your Printe
Page 13 and 14: 1-4 Rear View 1—Power switch 2—
Page 15 and 16: Printer Driver and Utility CD/DVD 2
Page 17 and 18: System Requirements 2-4 � Persona
Page 19 and 20: Uninstalling the Printer Driver (fo
Page 21 and 22: Using the Printer Driver 2-8 Common
Page 23 and 24: 2-10 Basic Tab The Basic Tab allows
Page 25 and 26: 2-12 � However, if the server is
Page 27 and 28: About the Control Panel 3-2 The con
Page 29 and 30: Message Window 3-4 The current stat
Page 31 and 32: 3-6 SPECIAL PAGES With this menu, p
Page 33: 3-8 �� All factory default valu
Page 37 and 38: NETWORK 3-12 With this menu, interf
Page 39 and 40: 3-14 DHCP: Settings ON/OFF Select w
Page 41 and 42: CONSUMABLE USAGE 3-16 With this men
Page 43 and 44: 3-18 INTERFACE
Page 45 and 46: Media Specifications What types and
Page 47 and 48: Media Types 4-4 Keep media on a fla
Page 49 and 50: 4-6 Driver Media Type Envelopes Pri
Page 51 and 52: 4-8 DO NOT use label sheets that
Page 53 and 54: 4-10 � Folded or wrinkled Glossy
Page 55 and 56: 4-12 Envelopes Envelopes can only b
Page 57 and 58: 4-14 Loading Plain Paper 1 Slide th
Page 59 and 60: 4-16 �� For envelopes with the
Page 61 and 62: 4-18 4 Insert the media as far as p
Page 63 and 64: 4-20 5 Slide the media guides again
Page 65 and 66: 4-22 4 Load the paper face up in th
Page 67 and 68: Duplexing 4-24 Select paper with hi
Page 69 and 70: Output Tray 4-26 All printed media
Page 71 and 72: 4-28 Media Storage
Page 73 and 74: Replacing Consumables 5-2 Note Fail
Page 75 and 76: 5-4 When replacing a toner cartridg
Page 77 and 78: 5-6 Keep toner cartridges: � In t
Page 79 and 80: 5-8 2 Open the printer’s front co
Page 81 and 82: 5-10 7 Remove the toner cartridge f
Page 83 and 84: 5-12 12 Make sure that the new tone
Page 85 and 86:
5-14 Replacing the Waste Toner Bott
Page 87 and 88:
5-16 6 Close the front cover. �
Page 89 and 90:
5-18 3 While continuing to press th
Page 91 and 92:
5-20 Replacing the Transfer Belt Un
Page 93 and 94:
5-22 5 Insert the protective sheet
Page 95 and 96:
5-24 11 Push up the guides. 12 Pull
Page 97 and 98:
5-26 16 Reconnect the power cord, a
Page 99 and 100:
5-28 4 Open the fuser unit cover. 5
Page 101 and 102:
5-30 10 Lift up the two levers. 11
Page 103 and 104:
5-32 Replacing Consumables
Page 105 and 106:
Maintaining the Printer 6-2 CAUTION
Page 107 and 108:
Cleaning the Printer 6-4 CAUTION Be
Page 109 and 110:
6-6 3 Close the tray. Cleaning the
Page 111 and 112:
6-8 5 Open the printer’s front co
Page 113 and 114:
6-10 10 Close the front cover. �
Page 115 and 116:
6-12 Cleaning the Printer
Page 117 and 118:
Introduction 7-2 This chapter provi
Page 119 and 120:
Understanding the Media Path 7-4 Un
Page 121 and 122:
7-6 Media Misfeed Messages and Clea
Page 123 and 124:
7-8 CAUTION The area around the fus
Page 125 and 126:
7-10 6 Load the media face up in Tr
Page 127 and 128:
7-12 Clearing a Media Misfeed from
Page 129 and 130:
7-14 �� If the misfed media can
Page 131 and 132:
7-16 6 Close the fuser unit cover.
Page 133 and 134:
7-18 Clearing a Media Misfeed from
Page 135 and 136:
7-20 3 Close the right side cover.
Page 137 and 138:
7-22 Symptom Cause Solution Media i
Page 139 and 140:
Solving Other Problems �� For d
Page 141 and 142:
7-26 Symptom Cause Solution Not all
Page 143 and 144:
7-28 Symptom Cause Solution Media i
Page 145 and 146:
7-30 Symptom Cause Solution Image i
Page 147 and 148:
7-32 Symptom Cause Solution There a
Page 149 and 150:
7-34 Symptom Cause Solution The col
Page 151 and 152:
7-36 This message... means... do th
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Technical Specifications A-2 Printe
Page 159 and 160:
A-4 Amperage 120 V: 8.3 A or less 2
Page 161 and 162:
A-6 �� Whether printing in colo
Page 163 and 164:
Index C Configuration menu ........
show all

magicolor 3730DN User's Guide - Konica Minolta

Create successful ePaper yourself

Delete template?

Save as template?