SERVICE MANUAL MR-G57N-T-NZ - B.d.t.
SERVICE MANUAL MR-G57N-T-NZ - B.d.t.
SERVICE MANUAL MR-G57N-T-NZ - B.d.t.
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Freezer compartment<br />
[2]<br />
Compressor does not operate<br />
[3]<br />
Filter board<br />
CN1 CN12<br />
Noise filter<br />
Poor cooling<br />
1 Is the set temperature of freezer compartment set to “High”?<br />
Yes<br />
2<br />
3<br />
Does cool air come out of air outlet when opening the refrigerator<br />
compartment door and attaching a magnet bar on the door switch ?<br />
Yes<br />
Check freezer compartment thermistor.<br />
Dip freezer compartment thermistor into ice water (0 ), and<br />
measure the resistance between terminal (white) and<br />
(white) by detaching 4-pin connector at the left-back bottom of<br />
vegetable compartment.<br />
•Resistance at 0 :approx. 6~7k .<br />
Defective thermistor<br />
Replace freezer compartment thermistor<br />
Not cooling at all (In case any error codes doesn’t appear as shown in page 29,30 even though Ice select switch is pressed for 5 seconds)<br />
Does AC 230V run between and , terminals<br />
of CN1 on filter board?<br />
Yes<br />
Does AC 230V run between and , terminals<br />
of CN12 on filter board?<br />
Yes<br />
Detach each connector CN2A on<br />
control board check the continuity<br />
between terminals and<br />
respectively.<br />
(Check if there is a short or open<br />
circuit in the motor protector.)<br />
Continuity detected<br />
Detach connector CN50G on control<br />
board and check the resistance<br />
respectively between terminals of<br />
, and :approx. 9.3<br />
Continuity detected<br />
Check the error display of selfcheck<br />
after turning on and off the<br />
power supply.<br />
With all the connectors connected.<br />
Inverter-related parts may be<br />
defective. Conduct ice making<br />
test operation. (See page 29,30<br />
for error codes.)<br />
No<br />
continuity<br />
No<br />
No<br />
Control board<br />
6-pin connector in machine chamber<br />
CN2A CN50G<br />
Control board<br />
28<br />
No<br />
No<br />
Normal<br />
CN7S<br />
Abnormal<br />
Set the temperature to “High”.<br />
Proceed to “The refrigerator fan motor does not work.”<br />
When compressor<br />
operates, display<br />
indicates E41 as a<br />
result of self-check.<br />
M<br />
Compressor<br />
M Motor<br />
protector<br />
Normal<br />
Abnormal<br />
Normal<br />
4-pin connector<br />
Yes<br />
Is refrigerator in the demonstration mode? Release the demonstration mode. (See page 11.)<br />
No<br />
No<br />
continuity<br />
Inspect power-supply wiring such as power cord and<br />
breaker etc.<br />
Replace the filter board.<br />
Motor protector (open circuit)<br />
By measuring the resistance,<br />
ensure that the circuit is open.<br />
Disconnect 6-pin connector<br />
in machine chamber to check<br />
resistance between terminals of<br />
, and : approx. 9.3<br />
Abnormal<br />
Measure the resistance of compressor’s<br />
winding between terminals<br />
of black, white, and red :<br />
approx. 9.3<br />
Check connector contact.<br />
Exchange the unit<br />
Replace solenoid<br />
valve coil.<br />
Freezer<br />
compartment<br />
thermistor<br />
Replace the lead wire<br />
assembly (Lead wire of<br />
compressor)