SERVICE MANUAL MR-G57N-T-NZ - B.d.t.

More documents

Recommendations

Info

OPERATING PROCEDURE PHOTOS Control panel Duct R (4) Remove rivet , and pull out the mirror hinge on the lower left of the control panel to remove the connector. (See photo 11) (5) Remove rivet (2 rivets) in the upper left and right side, screw (1 screw) in the lower left side. Detach catches (5 places). (See photo 11) Lamp thermistor holder (6) Remove 3 screws and 4 catches. (See photo 12) Control panel assembly (The assembly consists of the following: Control panel, and duct R). Caution on assembly To prevent poor contact of connectors, connect them properly. Fix the control panel by inserting the lower catches (2 places) into the floor of refrigerator compartment. 4. Parts inside the ice making compartment, versa compartment, vegetable compartment, and freezer compartment Partition I/S cover Partition I/ S Partition I/ S/ V Cover (IM) Automatic ice maker assembly Cover (lower) Partition V/ F Connector cover (right/ left) Fan grille Defrost heater, Drip tray, DEF thermistor (1) Remove interior parts out of ice making compartment, versa compartment, vegetable compartment, and freezer compartment. (2) To detach them, pull out the doors of ice making compartment, versa compartment, vegetable compartment, and freezer compartment. Partition I/ S cover (3) Remove screw (2 screws) at the front of the refrigerator and 4 rollers. Remove the catches at the both sides of partition I/S cover. (Remove them with a driver or another tool, which is wrapped in cloth in order to protect the cover surface from scratches. (See photo 13) Partition I/ S (4) Remove the catches on the upper and lower right of the partition I/S (See photo 14), and then slide the partition I/S toward right while being careful not to deform or damage the pipe. (See photo 15) Deforming or damaging the partition I/S causes refrigerant leakage or failure of cooling. Caution on assembly Do not deform or damage the pipe. (See photo 14) Deforming or damaging the pipe causes refrigerant leakage or failure of cooling. Install the partition I/S so that the arrow points up. (See photo 13) 44 Photo 11 Photo 12 Photo 13 Photo 14 Photo 15 Rivet Screw Pipe Rivet Catch Screw Screw Screws Catch Catch Rollers Mirror hinge Catches A r r o w Catch Control panel Catch Catch Catch Rivet Catch Catch Lamp thermistor holder Screw Catch Partition I/S cover Pipe Rollers Partition I/S Partition I/S Move to right
OPERATING PROCEDURE PHOTOS Partition I/ S/ V (5) Remove screw (2 screws) at the front of refrigerator. Remove screw (1 screw each) and screw (1 screw each) at the right and left side of inner wall. Then lift up the partition. (See photo 16) Cover (IM) (6) Remove 2 rivets and 3 catches in order to detach the cover. (See photo 17) Automatic ice maker assembly (7) Remove 1 rivet and pressing 2 catches upward, and pull Automatic ice maker assembly to the right side. (See photo 17) Cover (upper) (8) Remove rivet (1 rivet) to detach the cover (See photo 18) Cover (lower) (9) Remove rivet (1 rivet) to detach the cover (See photo 19) Partition V/ F (10) Remove screw (4 screws) on inner wall and screw (2 screws) at the front. Detach three connectors and lift up the partition. (See photo 18) Connector cover (right/ left) (11) To detach connector cover, remove rivet (2 rivets each) and catches (2 places). (See photo 19) (12) Detach the connector. Fan grille (13) To detach fan grille, remove screw (2 screws) on right and left side, rivet (1 rivet) on left side, and detach upper catches (3 places). Fan grille consists of the following: motor dampers (for ice- making compartment/ refrigerator compartment, versa compartment), refrigerator fan motor, fan, thermal fuse, vegetable compartment heater 1, duct heater, 4 thermistors. (See photo 19) 45 Photo 16 Photo 17 Photo 18 Photo 19 Screw Tank holder Tank holder Rivet Pipe Cover (upper) Rivet Screws Screws Screws Partition I/ S/ V Rivet Cover (IM) Partition V/F Screws Catches Catch Screw Fan grille Catches (Automatic Ice maker assembly) Automatic Ice maker assembly Catches Rivet Rivet Connector cover (left) Rivet Cover (lower) Connector cover (right) Screws Rivet Fan grille (Fan grille consists of the following: motor dampers (for ice making compartment / refrigerator compartment, versa compartment), refrigerator fan motor, fan, thermal fuse, vegetable compartment heater 1, duct heater, 4 thermistors).
Page 1: HOME REFRIGERATOR SERVICE MANUAL Mo
Page 4 and 5: 2 SPECIFICATIONS MR-G57N-NZ Accesso
Page 6 and 7: 3 MR-G57N-NZ WIRING DIAGRAM I.THERM
Page 8 and 9: 4 MR-G57N-NZ 86 203 196 OUTLINES AN
Page 10 and 11: 6 TROUBLESHOOTING 6-1 FUNCTION OF O
Page 12 and 13: (5) Service Check Function 1) Outli
Page 14 and 15: 3) Damper Operation Mode Setting Wi
Page 16 and 17: 4) Thermistor temperature check mod
Page 18 and 19: Switching over the mode Press to se
Page 20 and 21: (3) Select the adjustment level of
Page 22 and 23: (2) Timing in self-check Trouble of
Page 24 and 25: Display Error Display code Tens' pl
Page 26 and 27: (3) Operation by ice making test Pr
Page 28 and 29: Freezer compartment [2] Compressor
Page 30 and 31: Inverter-related indication “Comp
Page 32 and 33: Vegetable compartment [6] Is the te
Page 34 and 35: 6-6 TROUBLE CRITERION OF MAIN PARTS
Page 36 and 37: Components/ Part Name Vegetable com
Page 38 and 39: Components/ Part Name Three-way val
Page 40 and 41: 6-8 TEST POINT DIAGRAM OF CONTROL B
Page 42 and 43: 8 DISASSEMBLY INSTRUCTIONS MR-G57N-
Page 46 and 47: OPERATING PROCEDURE PHOTOS Evaporat
Page 48 and 49: OPERATING PROCEDURE 5. Parts inside
Page 50 and 51: OPERATING PROCEDURE 9. Compressor c
Page 52: Door adjustment • Common element

SERVICE MANUAL MR-G57N-T-NZ - B.d.t.

Create successful ePaper yourself

Delete template?

Save as template?