SEC-400series - Shavo Technologies
SEC-400series - Shavo Technologies
SEC-400series - Shavo Technologies
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
MFT-20<br />
Mass flow checker<br />
When there is a suspected problem with a mass flow controller, it is<br />
necessary to check the power source, display unit, settings unit,<br />
cables, and <strong>SEC</strong> itself for malfunctions, in order to determine<br />
the cause of the problem. The MFT-20 can drive the <strong>SEC</strong> and monitor<br />
its input and output voltage, while carrying out the necessary control<br />
functions to determine if the <strong>SEC</strong> is operating properly. This allows<br />
the user to determine if the source of a problem is the <strong>SEC</strong> itself or<br />
the power source, before detaching the <strong>SEC</strong> from the equipment<br />
piping. An internal potentiometer enables control of the <strong>SEC</strong> as well.<br />
sEnables easy checking of the mass flow controller without detaching<br />
the piping connections.<br />
sNo power source required.<br />
sCan open and close the valve.<br />
sAuto-zero function is available (only for the <strong>SEC</strong>, which features<br />
an auto-zero function).<br />
Display<br />
Internal standard voltage<br />
Power source voltage<br />
Power drain<br />
Weight<br />
Operating temperature<br />
80 +2<br />
-1<br />
4 3 2 1 10<br />
+2<br />
125 -1<br />
5 6<br />
7<br />
sAccessories<br />
PAC-S6<br />
Multifunctional control unit<br />
DC 20 V full scale/LCD display<br />
+5 VDC<br />
+7 to +30 VDC (normally used with +15 V mass flow controllers)<br />
6 mA or lower, in the voltage range shown above<br />
400 g<br />
0 to 50°C<br />
8<br />
9<br />
1 External output pin<br />
2 Alarm display LED<br />
3 Relay cable connector<br />
4 Voltage display LCD<br />
5 Check point switching switch<br />
6 Flow rate settings unit<br />
7 Input switching switch<br />
8 Valve control switching switch<br />
9 <strong>SEC</strong> selection switch<br />
10 Auto-zero switch<br />
11 Attachment magnet<br />
The PAC-S6 is a multifunctional control unit that includes everything<br />
needed for mass flow controller control, including a power source,<br />
display unit, and settings unit.<br />
sMulti-range function sFlow rate settings function: Five presets sProgram control<br />
function sFlow rate alarm output function sSoftware slow start function sFlow rate<br />
control valve: Fully open/fully closed sFlow rate display: SET/OUT switching function<br />
sComplies with DIN standards.<br />
30<br />
11<br />
sUsing the MFT-20<br />
Existing signal cable<br />
<strong>SEC</strong><br />
Cable adapter<br />
PAC-D1/D2<br />
Control units<br />
Mass Flow Controllers 24<br />
Attachment cable, 2 m<br />
Cable adapters<br />
Model no. Used with<br />
CA-H<br />
<strong>SEC</strong>-4400/7300<br />
8000/E series<br />
CA-4 <strong>SEC</strong>-400 series<br />
*Cable adapter is optional.<br />
The PAC-D1 and PAC-D2 are control units that feature functions used<br />
frequently with mass flow controllers, as well as a power source,<br />
display unit, and settings unit.<br />
PAC-D1: For SEF/LF series of mass flow meters<br />
PAC-D2: For <strong>SEC</strong>/LV series of mass flow controllers<br />
sFlow rate settings function sFlow rate alarm: Contact point output available<br />
sCompact sFlow rate control valve sFlow rate control valve: Fully open/fully closed<br />
sFlow rate display: SET/OUT switching function