SEC-400series - Shavo Technologies

49
ANALYSIS
FG-100 series
Model
Measurement principle
Detector
Measured frequency range
Cell optical path length
(cell capacity)
Cell window material
O-ring material
Piping attachment
Frequency resolution
Operating temperature range
Operating humidity range
Power source
Power consumption
Nitrogen gas
Liquid nitrogen
Mass
Standards
* These products are manufactured by HORIBA Ltd. * Viton ® is registered trademark of E. I. DuPont de Nemours.
IR-150 series
Model
Gases and densities *1
Calibration gas
Measurement method
Measurement cell length
Repeatability
Response speed
Pressure resistance
Display
Output signal
Temperature
Temperature resistance
Gas connection
Leak rate
Power source
External dimensions
Mass
FG-110 FG-120
Liquid nitrogen cooled MCT
Standard: 5000 to 700 cm-1 ; Option: 5000 to 600 cm-1 240 VA (2.4m cell)
IR-150S IR-150L
TMAI, TMGa, THIn, 12%
DMZn 18%
5 mm
153.5 x 37.5 x 107 mm (H x W x D)
About 1.0 kg
FTIR method
Single cell: 0.01 m (7 mL), 0.1 m (70 mL), 0.8 m (300 mL), 2.4 m (300 mL), 10 m (1800 mL)
Dual cell: 0.01 m + 2.4 m, 0.01 m + 0.8 m, 0.1 m + 2.4 m
Standard: BaF2; Option: ZnSe
Standard; Viton ® ; Option: Kalrez
Standard: 1/4" Swagelok; Option: 1/4" VCR
0.5, 1, 2, 4, 8, 16 (cm-1)
25 ± 5°C
70% RH or lower
AC 100 ± 10 V, 50/60 Hz (different standards available for overseas)
For analysis meter purge: About 5 L/min at all times; For calibration: 5 L/min when required: Nitrogen gas requirements: 99.99% or higher, moisture below –30°C saturation levels, no dust or mist
500 to 600mL range (duration 8 to 10 hours)
Single cell type: 40 kg (2.4 m cell); Dual cell type: 50 kg
CE markings, FC Part 15 (Class A)
C3H8
Non-dispersive infrared (NDIR) method
± 2% F.S.
40 sec (T90), typically 20 sec
0.05 to 0.15 MPa (G)
100 to 5000, can be set as desired
0 to 5 V
Max. 60°C or lower
Max. 70°C or lower
SUS-316L, sapphire glass, silver
5 x 10-12 Pa·m3 /s (He) or lower
AC 100 V
Standard Fitting
1/4" VCR Type Male or equivalent
*1 Maximum output at each cell length. * Gas settings other than those described above are possible. Please contact HORIBA STEC for more information.
External dimensions
Electrically cooled MCT
5000 to 900cm-1 250 VA (2.4m cell)
TMAI, TMGa, THIn, 1.2%
DMZn 1.8%
50 mm
163 x 36.5 x 158 mm (H x W x D)
About 1.7 kg
sFG series sIR-150S sIR-150L
350
350
633
• Single cell type
• Dual cell type
• Sampling unit
450 400
Analysis unit Cell unit
* Dimensions may vary with specifications
(cell optical path length).
600 400
Analysis unit Cell unit
(For single cell type)
(For dual cell type)
500 650
700
16.2
10.65
65.5
107±0.5
Bottom screw
attachment positions
8.45
48.6
35.5
2-M5
153.5±1
157.5±2
18.75
37.5
16
10.25
115.5
158±0.5
Bottom screw
attachment positions
31.45 52.6
4-M4
23.4
163±1
167±2
17.85
36.5