1 - Cash Registers

More documents

Recommendations

Info

6 5 6 Displays Operator display Receipt OFF indicator Repeat / Sentinel mark / Power save mark • Clerk code or Mode name The mode you are in is displayed. When a clerk is assigned, the clerk code is displayed in the REG or OP X/Z mode. For example, “?01?” is displayed when clerk 01 is assigned. • Repeat The number of repeats is displayed, starting at “2” and incremental with each repeat. When you have registered ten times, the display will show “0”. (2 ➞ 3 ......9 ➞ 0 ➞ 1 ➞ 2...) • Sentinel mark When amount in the drawer reaches the amount you preprogrammed, the sentinel mark “X” is displayed to advice you to remove the money to a safe place. • Power save mark When the cash register goes into the power save mode, the power save mark (decimal point) lights up. • Function message display area Item labels of departments and PLU/subdepartments and function texts you use, such as %1, (-) and CASH are displayed. For the details of function texts, please refer to pages 43 and 44. When an amount is to be entered or entered, “AMOUNT” is displayed: When an amount is to be entered, ------- is displayed at the numeric entry area with “AMOUNT”. When a preset price has been set, the price is displayed at the numeric entry area with “AMOUNT”. • Numeric entry display area Numbers entered using numeric keys are displayed here. Date and time display Date and time appear on the display in the OP X/Z, REG, or MGR mode. In the REG or MGR mode, press the s key to display the date and time. Error message When an error occurs, the corresponding error message is displayed in the function message display area. For details of error messages, please refer “Error message table” on page 69. Customer display (Pop-up type) Drawer Lock Key This key locks and unlocks the drawer. To lock it, turn 90 degrees counterclockwise. To unlock it, turn 90 degrees clockwise. Clerk code or mode name Power save mark (Lighting the mark only under the power save mode) SK1-1 Function message display area Numeric entry display area www.cashregisters.net
GETTING STARTED Please follow the procedure shown below. 1 Find a stable surface near an AC outlet where the cash register will not subject to water sources or direct sunlight . Unpack the cash register and make sure all accessories are included. For details of accessories, please refer to “Specifications” section. 2 Installing the cash register Initializing the cash register In order for the cash register to operate properly, you must initialize it before operating for the first time. Follow this procedure. 1. Make sure the power cord plug is not inserted into the AC outlet. 2. Insert the manager (MA) key into the mode switch and turn it to the PGM position. 3. While holding down both the } key and the l key, insert the plug into the AC outlet. The buzzer will sound three times and “??? MRS. ???” will be displayed. 4. The cash register has now been initialized. The register display will now show “0.00” with “PGM”. REG OPX/Z MGR OFF X1/Z1 VOID X2/Z2 If the buzzer does not sound when the plug is inserted, the initialization has not been done successfully. (This will occur when the voltage is high because you operated the cash register before starting initialization.) Wait at least ten seconds after pulling out the plug and initialize the cash register again. The cash register has a built-in memory protection circuit which is operated by rechargeable batteries. Since the rechargeable batteries have been discharged, please charge the batteries for one or two days before using the cash register for the first time. To charge the batteries, set the mode switch to a position other than “OFF” with the power cord plugged into the AC outlet. Unless the batteries have been charged, all of the programmed data and sales data is not saved. If you press a key by mistake, an error message such as “HEAD UP” or “PAPER EMPTY” may be displayed. Press the l key to clear message after installing paper rolls. PGM *** MRS. *** PGM 0.00 www.cashregisters.net 7
Page 1 and 2: ELECTRONIC CASH REGISTER CAJA REGIS
Page 3 and 4: WARNING FCC Regulations state that
Page 5 and 6: FOR THE MANAGER PRIOR TO PROGRAMMIN
Page 7: 3 The mode switch can be operated b
Page 11 and 12: 5. Set a paper roll in the paper ro
Page 13 and 14: FOR THE OPERATOR OVERVIEW OF FLOW O
Page 15 and 16: Clerk assignment Prior to any item
Page 17 and 18: Example: Selling a dept. 12 item ($
Page 19 and 20: Single item cash sale (SICS) entry
Page 21 and 22: 6 Tax Calculation Automatic tax Whe
Page 23 and 24: OPTIONAL FEATURES 1 Auxiliary Entri
Page 25 and 26: 2 Key operation example Currency co
Page 27 and 28: CORRECTION 1 If you make an incorre
Page 29 and 30: FOR THE MANAGER PRIOR TO PROGRAMMIN
Page 31 and 32: Example: Programming the tax rate 4
Page 33 and 34: • If the tax is not provided for
Page 35 and 36: Commission group number • A commi
Page 37 and 38: *: Item: Selection: Entry: A Commis
Page 39 and 40: Percent rate limitation for % and &
Page 41 and 42: Function parameters for C, X, Y and
Page 43 and 44: 41 Alphanumeric character code tabl
Page 45 and 46: List of function texts Function no.
Page 47 and 48: Logo print format (6 types) Graphic
Page 49 and 50: *1 Enter job code using numeric key
Page 51 and 52: Job code: 62 * Item: Selection: Ent
Page 53 and 54: 3 Various Function Selection Progra
Page 55 and 56: (4) RS-232C start code and end code
Page 57 and 58: Sample printouts 1 Programming repo
Page 59 and 60:
READING (X) AND RESETTING (Z) OF SA
Page 61 and 62:
2 Daily Sales Totals Full sales rep
Page 63 and 64:
PLU report by associated department
Page 65 and 66:
OVERRIDE ENTRIES Programmed limit f
Page 67 and 68:
4 Replacing the Paper Roll Be sure
Page 69 and 70:
5 Caution: The paper cutter is moun
Page 71 and 72:
9 The malfunctions shown in the lef
Page 73 and 74:
Programming sheet for departments (
Page 75 and 76:
2 INDICE INTRODUCCION..............
Page 77 and 78:
4 3 El selector de modo funciona in
Page 79 and 80:
6 PARA EMPEZAR Siga el procedimient
Page 81 and 82:
Función de activación/desactivaci
Page 83 and 84:
10 Registros de venta en metálico
Page 85 and 86:
12 Cálculo porcentual para el subt
Page 87 and 88:
14 2 Podrá cancelar cualquier regi
Page 89 and 90:
16 Para borrar una tasa de impuesto
Page 91 and 92:
18 *2:Elemento: Selección: Registr
Page 93 and 94:
20 4 Programación de teclas miscel
Page 95 and 96:
22 *1:Elemento: Selección: Registr
Page 97 and 98:
24 Texto de sección (etiqueta de a
Page 99 and 100:
26 • Los ajustes iniciales son lo
Page 101 and 102:
28 Selección de función para tecl
Page 103 and 104:
30 Código de tarea: 66 * Elemento:
Page 105 and 106:
32 (4) Código inicial y código fi
Page 107 and 108:
34 LECTURA (X) Y REPOSICION (Z) DE
Page 109 and 110:
36 MANTENIMIENTO PARA EL OPERADOR 1
Page 111 and 112:
38 5. Inserte el extremo del papel
Page 113:
40 Tabla de mensajes de error Cuand
show all

1 - Cash Registers

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?