Sony STR-DN840 - STR-DN840 Istruzioni per l'uso Inglese
Sony STR-DN840 - STR-DN840 Istruzioni per l'uso Inglese
Sony STR-DN840 - STR-DN840 Istruzioni per l'uso Inglese
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Select “WRN Check” in step 2 in “Auto<br />
Calibration” (page 82), then press .<br />
If a warning message appears, check the<br />
message and use the receiver without<br />
change.<br />
Or if necessary, <strong>per</strong>form Auto Calibration<br />
again.<br />
When “Error Code” appears<br />
Check the error and <strong>per</strong>form Auto<br />
Calibration again.<br />
1 Press .<br />
“Retry ?” appears on the TV screen.<br />
2 Select “Yes”, then press .<br />
3 Repeat steps 1 to 3 in “Auto<br />
Calibration” (page 82).<br />
Message list after Auto<br />
Calibration measurement<br />
Display and explanation<br />
Error Code 30<br />
Headphones are connected to PHONES on<br />
front panel of receiver. Remove the<br />
headphones and redo Auto Calibration.<br />
Error Code 31<br />
The SPEAKERS is set to off. Set to other<br />
speaker settings and <strong>per</strong>form the Auto<br />
Calibration again.<br />
Error Code 32<br />
Error Code 33<br />
Speakers were not detected or not connected<br />
pro<strong>per</strong>ly.<br />
• None of the front speakers are connected or<br />
only one front speaker is connected.<br />
• Either the surround left or surround right<br />
speaker is not connected.<br />
• Surround back speakers or front high<br />
speakers are connected even though<br />
surround speakers are not connected.<br />
Connect the surround speaker(s) to the<br />
SPEAKERS SURROUND terminals.<br />
Display and explanation<br />
• The surround back speaker is connected<br />
only to the SPEAKERS SURROUND<br />
BACK/ BI-AMP/ FRONT HIGH/<br />
FRONT B R terminals. When you<br />
connect only one surround back speaker,<br />
connect it to the SPEAKERS<br />
SURROUND BACK/<br />
BI-AMP/ FRONT HIGH/ FRONT B L<br />
terminals.<br />
• Either the front left high or front right<br />
high speaker is not connected.<br />
The optimizer microphone is not<br />
connected. Make sure that the optimizer<br />
microphone is connected pro<strong>per</strong>ly and<br />
<strong>per</strong>form the Auto Calibration again.<br />
If the optimizer microphone is connected<br />
pro<strong>per</strong>ly but the error code still appears,<br />
the optimizer microphone cable may be<br />
damaged.<br />
Warning 40<br />
The measurement process has completed with<br />
high noise level detection. You may be able to<br />
achieve better results if you try in a quiet<br />
environment again.<br />
Warning 41<br />
Warning 42<br />
The input from the microphone is too big.<br />
• The distance between the speaker and the<br />
microphone may be too close. Set them<br />
apart and <strong>per</strong>form the measurement again.<br />
Warning 43<br />
The distance and position of a subwoofer<br />
cannot be detected. This may be caused by<br />
noise. Try to <strong>per</strong>form the measurement in a<br />
quiet environment.<br />
No Warning<br />
There is no warning information.<br />
Tip<br />
Depending on the position of the subwoofer, the<br />
measurement results may vary. However, there<br />
will be no problems even if you continue to use<br />
the receiver with that value.<br />
Adjusting Settings<br />
83 GB
Change language