18. Yoğun Madde Fiziği – Ankara Toplantısı, Orta Doğu Teknik Üniversitesi, 25 Kasım 2011Kuantum kuyu lazerlerin çift farklı yapılar kullanılarak incelenmesiSinan Yaşar 1 , İsmail Bilican 2 , Bünyamin Şahin 2 , Sedat Ağan 2 , ve İhsan Uluer 21 Mustafa Kemal Üniversitesi, Fen-Edebiyat Fakültesi, Fizik Bölümü, Hatay2 Kırıkkale Üniversitesi, Fen- Edebiyat Fakültesi, Fizik Bölümü, KırıkkaleP12Bu çalıĢmada, günümüzde nano teknolojik uygulamalarda bir çok araĢtırmacının dikkatleriniüzerine çeken kuantum kuyu lazerlerin simülasyon yoluyla üretimi ve analizi yapılmıĢtır. Buaçıdan mevcut çalıĢmalar takip edilmiĢ 5 ayrı farklı yapılı kuantum kuyu malzemesinin çeĢitlikompozisyon ve konfigürasyonlarda dizaynı ile 25 farklı yapı ayrı ayrı incelenmiĢtir. Lazeryapılar simülasyonda dizayn edilirken Fabry–Parot ve Fabry–Parot Ridge tipi lazer yapıolarak iki farklı konfigürasyonda ele alınmıĢtır. Her yapının bölge bölge (aktif bölge, kuantumkuyu bölge, bariyer ve hapis bçlgeleri gibi) Bant–Enerji grafikleri ve değerleri, kırılma indislipr<strong>of</strong>ili ve değerleri, katkı oranları (n tipi ve p tipi bölgeler için) pr<strong>of</strong>ili ve değerleriüretilmiĢtir. Ayrı ayrı her yapıda kullanılan malzeme kompozisyonları tasarlanmıĢ ve iĢlemekonulmuĢtur. Ġstenilen sıcaklık değerleri ve taĢıyıcı yoğunlukları ayarlamarak malzemekazançları hesaplanmıĢtır. Pik–kazanç grafikleri ve verileri çıkarılmıĢtır. Kendiliğinden ıĢımagrafik ve değerleri üretilmiĢtir. Elde edilen tüm bu spnuçlar literatürle karĢılĢatırılmıĢ veuyum içerisinde olduğu görülmüĢtür.44
18. Yoğun Madde Fiziği – Ankara Toplantısı, Orta Doğu Teknik Üniversitesi, 25 Kasım 2011Role <strong>of</strong> annealing time and temperature on structural and superconductingproperties <strong>of</strong> (Bi,Pb)-2223 thin films produced by sputteringG. Yildirim * , A. Varilci, M. Akdogan, S. Bal, G. Ozdemir, C. Terzioglu, M. Dogruer**,and E. Yucel*Abant Izzet Baysal University, <strong>Department</strong> <strong>of</strong> <strong>Physics</strong>, Bolu–Turkey 14280**Mustafa KemalUniversity, <strong>Department</strong> <strong>of</strong> <strong>Physics</strong>, Hatay–Turkey 31034P13This study reports the effect <strong>of</strong> annealing time (15 m, 1.5 h, and 3 h) and temperature (850,860, and 870 °C) on the structural and superconducting properties <strong>of</strong> thin films by means <strong>of</strong>scanning electron microscopy (SEM), X-ray analysis (XRD), electron dispersive X-ray(EDX), resistivity and transport critical current density (J c ) measurements. Zero resistivitytransition temperatures (T c ) <strong>of</strong> the films produced are estimated from the dc resistivitymeasurements. In addition, the phase and lattice parameters are determined from XRDpatterns when the microstructure, surface morphology and element composition analyses <strong>of</strong>the samples are investigated by SEM and EDX measurements, respectively. The resultsindicate that T c values <strong>of</strong> the films obtained are observed to be in a range <strong>of</strong> 23–102 K. The T c<strong>of</strong> the film annealed at 870 °C for 3 h is found to be the smallest (23 K) while the filmannealed at 860 °C for 3 h is noted to obtain the maximum T c value (102 K). On the otherhand, the maximum (minimum) J c is found to be about 2068 A/cm 2 (20 A/cm 2 ) for the filmannealed at 860 °C for 3 h (870 for 3 h). Moreover, according to the refinement <strong>of</strong> cellparameters done by considering the structural modulation, the greatest Bi-2223 phase fractionis noticed to belong to the film annealed at 860 °C for 3 h. Furthermore, SEM measurementsshow that the best surface morphology, largest grain size and grain connectivity are observedfor that film. Based on these results, T c and J c values <strong>of</strong> the samples studied are found todepend strongly on the microstructure. As for EDX results, the elements used for thepreparation <strong>of</strong> samples are observed to distribute homogeneously. The aim <strong>of</strong> this study is notonly to investigate the changes <strong>of</strong> structural and superconducting properties <strong>of</strong> the filmsproduced in the varied time and temperature but also to determine the best ambient for thefilm fabrication and show the feasibility <strong>of</strong> obtaining Bi-2223 film with tailored structure.45