Installation and start-up - Stange Energietechnik GmbH

More documents

Recommendations

Info

5.2 Environment Camino Generator 1. The place of installation for the SET-CAMINO Generator shall provide sufficient space so that all maintenance points are readily accessible. 2. The ambient temperature at the place of installation or in the room should not exceed 20 °C. 3. Higher ambient temperature will reduce the output of the Diesel engine. If the room temperature exceeds 20 °C, provide for a separate combustion air supply. The soundproofing hood of the SET-CAMINO Generator is provided with a socket where the combustion air must be supplied via the external air filter. 4. At a length of approx. 3 m of the supply line, a diameter 40 mm venting hose can be used. Insulation The venting hose shall be mechanically resistant and installed without bends, if possible. The SET-CAMINO Generator is installed in a soundproofing hood and does not require any additional insulation at the place of installation. When positioning the generator make sure that maintenance work and checks can be carried out without hindrance. Please test the following after positioning: − Air filter replacement − Fuel filter replacement − Oil filter replacement − Vee belt replacement − Coolant bleeding − Fuse replacement − Oil check 03-04-01 Installation of the SET Camino Generator 5-32
5.3 Foundation Camino Generators A solid foundation is required in order to transmit the forces generated by the SET Camino Generator to as large an area as possible. Advantageous foundations and suitable points of the vehicle bottom are the following: − solid steel plate (approx. 10 mm) − glued wooden plate − Screen printing plate min. 30 mm Avoid cavities below the foundation. Carefully screw the foundation to the base area. The generator has been supplied with a machine frame at which vibration metal elements are mounted. The vibration metal elements prevent solid borne noise from transmission onto the vehicle. Dimensions of machine frame:* * (refer also to dimensional sheet and technical data) 03-04-01 Installation of the SET Camino Generator 5-33
Page 1 and 2: Installation and start-up manual SE
Page 3 and 4: Table of contents Camino Generators
Page 5 and 6: 1 Introduction Camino Generators Pr
Page 7 and 8: Camino Generators 8. The unit shall
Page 9 and 10: 2.3 Basic duties Camino Generators
Page 11 and 12: 2.5 Hints for specific types of dan
Page 13 and 14: 2.6.5 Environmental protection Cami
Page 15 and 16: 3.2 Protective measures against mec
Page 17 and 18: 3.4.2 Electrical installation of th
Page 19 and 20: 3.8 Safety notes, summary Camino Ge
Page 21 and 22: 4 Installation data 4.1 Technical d
Page 23 and 24: • 4.2 Technical installation data
Page 25 and 26: 4.3 Dimensions „cooler unit examp
Page 27 and 28: 4.4.2 Cooling system connections Ca
Page 29 and 30: 4.4.4 Exhaust gas system connection
Page 31: 5 Installation of the SET Camino Ge
Page 35 and 36: 5.4.1 Direction of delivery of the
Page 37 and 38: 5.4.3 Piping at the cooling circuit
Page 39 and 40: 5.5 Installation of external air fi
Page 41 and 42: 5.7 Installation of the fuel system
Page 43 and 44: Camino Generators 4. Connect the su
Page 45 and 46: 6.1 Installation of control panel C
Page 47 and 48: Terminal box Line 1 = + 12 V Line 2
Page 49 and 50: 6.3 Electrical system of the vehicl
Page 51 and 52: 6.5 Mounting and installation of th
Page 53 and 54: 7 Initial start-up Camino Generator
Page 55 and 56: 7.2 Operation General Camino Genera
Page 57 and 58: 7.3.1 For initial start proceed as

Installation and start-up - Stange Energietechnik GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?